Attain 400 WG
- Manufacturer
- Imtrade
- Category
- Herbicides
- Registered until
- 2025-06-29
- Registration number
- 60140
- Active materials
- tralkoxydim400 g/kg
GENERAL INSTRUCTIONS - Imtrade Attain 400 WG Herbicide
MIXING:
- Use sprayers in good condition with high capacity agitation.
- Clean sprayer as per label instructions on the previously used product.
- Use only clean water for the spray solution.
- Ensure all in-line strainers and nozzle screens are 100 mesh or coarser.
- DO NOT use cartridge or disc filters after the spray tank outlet.
- Begin filling the spray tank with clean water and engage agitator.
- Add Imtrade Attain 400 WG Herbicide slowly when the sprayer is half full.
- DO NOT premix; add the total required amount before other herbicides or Supercharge®.
- Wait one minute after adding Attain 400 WG Herbicide before adding other products.
- Add recommended broadleaf weed herbicide or insecticide if tank mixing.
- Slowly add Supercharge® last, in at least 10 times its volume of water.
- Continue filling the tank with water.
SPRAYING INSTRUCTIONS: Ground Equipment:
- Apply in a spray volume of 50-150L of water per hectare at 250-350 kPa pressure.
- Use flat fan nozzles (e.g., Spraying Systems 110-01, 110-015, 110-02).
- DO NOT use 110-03 or larger nozzles; avoid floodjet nozzles, boomless jets, or misters.
- Nozzles may be angled forward 45°C for better penetration and coverage.
- Ensure continuous agitation during the entire spraying procedure.
- If agitation is stopped for more than 5 minutes, re-suspend the solution before spraying.
- Spray mixtures of Attain 400 WG Herbicide and Supercharge® can be left overnight.
Aerial Equipment:
- Apply through boom or Micronair units in 20-30L of water per hectare.
- Higher volume is preferred for more reliable results.
- Droplet size should be 200-250 microns (VMD), and swath width should not exceed recommendations.
- Weed control may not be as good as ground application.
CROP SAFETY:
- Yellowing or growth retardation may occur if applied to stressed crops or crops with less than 2 true leaves (Z12).
- Crops usually recover without loss in yield; avoid double spraying.
PLANTBACK PERIODS:
- DO NOT plant Sorghum, Maize, or Rice for four weeks after Imtrade Attain 400 WG application.
- Allow at least 10 days between Attain 400 WG application and other herbicides or fertilizer treatment.
RESISTANT WEEDS WARNING:
- Imtrade Attain 400 WG Herbicide is a Group A Herbicide.
- Resistant weed biotypes may exist due to genetic variability; continuous use may lead to resistant weeds.
- Imtrade Australia Pty Ltd is not liable for losses due to failure in controlling resistant weeds.
STORAGE AND DISPOSAL (5 kg):
- Store in a locked, dry, cool, well-ventilated area away from children, animals, food, and fertilizers.
- DO NOT store in prolonged direct sunlight.
- Dispose of undiluted chemicals properly; puncture or shred and bury empty bags in a landfill.
STORAGE AND DISPOSAL (50 kg):
- Store as mentioned for 5 kg; triple rinse containers before disposal.
- Dispose of undiluted chemicals properly; bury empty containers in a landfill.
SAFETY DIRECTIONS:
- Harmful if swallowed; will irritate eyes.
- If product gets in eyes, wash immediately with water.
- When preparing the spray, wear a face shield and goggles.
- Wash hands after use; wash face shield and goggles after each day's use.
Registered for cultures | Rate |
---|---|
Winter wheat | 0.25 - 0.5 kg |
Spring wheat | 0.25 - 0.5 kg |
Spring barley | 0.25 - 0.5 kg |
Winter barley | 0.25 - 0.5 kg |
Winter rye | 0.25 - 0.5 kg |
Spring rye | 0.25 - 0.5 kg |
Winter triticale | 0.25 - 0.5 kg |
Spring triticale | 0.25 - 0.5 kg |