Insight 750 SG

Manufacturer
Ruralco
Category
Herbicides
Registered until
2024-06-29
Registration number
81837
Active materials
Links

GENERAL INSTRUCTIONS

MIXING

Measure the required quantity of granules by weighing on scales. RELYON CLOPYRALID 750 SG HERBICIDE granules are highly soluble in water and will dissolve rapidly once added to fast-moving water. Maintain agitation at all times, including during mixing as well as spraying.

Spray Rigs with Premix Hoppers

For spray rigs that have a drop-down chemical induction hopper, three-quarter fill this hopper with water and have the rinsing sprinkler operating. Add the RELYON CLOPYRALID 750 SG HERBICIDE and when dissolved, transfer this batch into the quarter-filled main tank. Continue to rinse the hopper until the entire product has washed through.

Spray Rigs with Limited Bypass Agitation

For spray rigs that have limited bypass agitation, then as for most granulated formulations, pre-dissolve the RELYON CLOPYRALID 750 SG HERBICIDE in a bucket before adding them to the main tank. Add RELYON CLOPYRALID 750 SG HERBICIDE while stirring until the granules have dissolved.

Tank-Mixes: the following order should be followed:

  1. Quarter fill the spray tank maintaining agitation.

  2. Add RELYON CLOPYRALID 750 SG HERBICIDE granules, using the mixing procedure above.

  3. Add Haloxyfop 520 if it is to be used in the tank-mix.

  4. Add water to half fill the spray tank.

  5. Add wettable powders, water dispersible granules, or suspension concentrates.

  6. Add other emulsifiable concentrates, including other selective grass herbicides.

  7. If Uptake* Spraying Oil is to be used, add this when the spray tank is half full.

  8. If other adjuvants or a wetting agent are to be used, then add these according to their label.

  9. Add water to bring to the final spray volume.

Only mix sufficient spray solution for immediate use and avoid storing.

COMPATIBILITY

Conventional Canola: RELYON CLOPYRALID 750 SG HERBICIDE + Haloxyfop 520 + Uptake Spraying Oil are compatible and selective.

Triazine Tolerant Canola: Atrazine + RELYON CLOPYRALID 750 SG HERBICIDE + Haloxyfop 520 + Uptake Spraying Oil are compatible and selective.

Clearfield Canola: OnDuty + RELYON CLOPYRALID 750 SG HERBICIDE are compatible and selective.

RELYON CLOPYRALID 750 SG HERBICIDE is compatible with the following:

  • BROADLEAF HERBICIDES: Fluroxypyr, Metsulfuron-Methyl, Bromoxynil, Bromoxynil/MCPA LVE, Chlorsulfuron, Glyphosate, MCPA amine, MCPA LVE, Paraquat, Paraquat/Diquat, Terbutryn, 2,4-D Amine, Broadstrike, Eclipse, Eclipse/MCPA LVE, MetsulfuronMethyl/MCPA LVE, Triclopyr 600, Atrazine, Simazine, Tordon 242, Tigrex.

  • GRASS HERBICIDES ON BROADLEAF CROPS: Haloxyfop 520, Clethodim 240, OnDuty, Atrazine, Simazine.

  • GRASS HERBICIDES IN CEREAL CROPS: Diclofop-Methyl, Tralkoxydim WG, Wildcat, Topik 240 EC, Tristar.

  • ADJUVANTS: Uptake Spraying Oil, BS 1000.

APPLICATION

BOOM SPRAYING CROP AND PASTURES

Apply RELYON CLOPYRALID 750 SG HERBICIDE in sufficient water to obtain good coverage. It should be applied by an accurately calibrated ground rig or aircraft, delivering 200 to 300-micron droplets and not less than 50 L/ha water volume for boom sprayers or not less than 20L/ha for aerial applications. Hardhead thistle – use a spray volume of 200 to 250 L/ha of water.

HIGH VOLUME HAND GUN

Apply the recommended mix to give full coverage of leaves and stems through a No. 6-8 tip at 700 to 1500 kPa. Spray volume for effective coverage of dense pasture weeds should be 10 to 15 liters of spray per 100m2 (10m x 10m) of infestation. For larger areas an equivalent would be 1000 to 1500 liters per infested hectare.

STEM INJECTION

To make a stem injection pocket at waist height, use a ¾ length axe with a blade width of 5 to 7 cm. The axe cut must be through the bark and deep enough to place all the chemicals in contact with the sapwood.

The chemical must be applied immediately after the injection pocket is made. Apply chemical with a Phillips 5mL vaccinator fitted with a tree injector kit, which can be accurately calibrated. Set vaccinator to deliver 1mL of the diluted mix.

When treating regrowth less than the width of the axe, ensure chemical does not run out the sides of the cut, as reduced control will result. This can be overcome by using the corner of the axe to make the pocket in the stem.

CLEANING SPRAY EQUIPMENT

RINSE WATER SHOULD BE DISCHARGED ONTO A DESIGNATED DISPOSAL AREA, OR IF THIS IS UNAVAILABLE, ONTO UNUSED LAND AWAY FROM DESIRABLE PLANTS AND WATER SOURCES.

PARTIAL CLEANING

Before spraying crops that are selective to RELYON CLOPYRALID 750 SG HERBICIDE. After using RELYON CLOPYRALID 750 SG HERBICIDE, empty the tank completely and drain the whole system. Thoroughly wash inside the tank using a pressure hose. Quarter fill the tank with clean water and circulate through the pump, line, hoses, and nozzles. Drain and repeat the procedure twice.

COMPLETE CLEANING

Before spraying crops that are susceptible to RELYON CLOPYRALID 750 SG HERBICIDE. After using RELYON CLOPYRALID 750 SG HERBICIDE, empty the tank completely and drain the whole system. Thoroughly wash inside the tank using a pressure hose. Quarter fill the tank with clean water and circulate as above, then drain. Quarter fill the tank again and add an alkali detergent (e.g., Surf®, Omo®, Drive®) at 500mL/100L water or 500g/100L water and circulate throughout the system for at least 15 minutes. Drain, remove filters and nozzles, and clean separately. Rinse inside the tank thoroughly using a pressure hose and flush the system with clean water. Chlorine-based cleansers are NOT recommended. Rinse water should be discharged onto a designated disposal area, or if this is unavailable, onto unused land away from desirable plants and water sources.

Registered for cultures
Canola