EnnobePlant Protection Product ComparisonPlant Protection Product ComparisonReport inaccuraciesReport inaccuracies

A dispersible concentrate containing 62.5 g/litre (5.7% w/w) epoxiconazole and

225 g/litre (20.6% w/w) prochloraz.

A systemic fungicide for use in winter wheat, spring wheat, winter barley, spring barley, triticale and rye.

 

IMPORTANT: This information is approved as part of the Product Label. All instructions within this section must be read carefully in order to obtain safe and successful use of this product. Ennobe is a systemic fungicide for use in winter wheat, spring wheat, winter barley, spring barley, triticale and rye.

Ennobe should not be applied to crops suffering from any other stress, such as drought or waterlogging, otherwise the crop may suffer from scorch from which recovery may not be complete.

A period of at least 3 hours (or longer in poor drying conditions) without rain should follow spraying otherwise results may be reduced.

This product may cause damage to broad-leaved plant species.

Avoid spray drift on to neighbouring crops.

Wash equipment thoroughly after use.

 

Ennobe is a systemic fungicide with protectant and curative properties for the control of a range of diseases in winter and spring wheat, winter and spring barley, rye and triticale as summarised below: Ennobe offers prolonged persistence of disease control leading to increased yield.

 

Disease:Powdery mildew 

Rate:Apply 1.8 litres Ennobe in 200 to 300 litres of water per hectare. 

Critical Comments:MC

 

Disease:Powdery mildew 

Rate:Apply 1.8 litres Ennobe in 200 to 300 litres of water per hectare. 

 

Strains of certain cereal diseases with decreased sensitivity to triazole fungicides are known to exist in the UK. Where these occur or develop Ennobe may not give satisfactory control.

Ennobe contains the DMI fungicides epoxiconazole and prochloraz. Resistance to some DMI fungicides has been identified in Septoria leaf blotch (Mycosphaerella graminicola) which may seriously affect the performance of some products. For further advice on resistance management in DMIs contact your agronomist or specialist advisor, and visit the FRAG-UK website.

 

Ennobe is a systemic fungicide with protectant and curative properties for use in winter wheat, spring wheat, winter barley, spring barley, triticale and rye.

Apply Ennobe at the start of foliar disease attack. Applications can be made up to and including flowering just complete in winter and spring wheat, rye and triticale and up to and including emergence of ear just complete in winter and spring barley.

For optimum effect against eyespot with Ennobe apply between the leaf sheaths erect and second node detectable stages of the crop.

For protection against Fusarium ear blight and sooty mould on the ears of winter and spring wheat, apply Ennobe during ear emergence.

For control of Septoria tritici and Septoria nodorum, treatment should normally be made after the third node detectable stage when disease is present and when weather favouring disease development has occurred. A follow-up treatment with an appropriate fungicide may be necessary if conditions continue to favour disease development.

Apply 1.8 litres Ennobe in 200 to 300 litres of water per hectare.

Qualified recommendation Ennobe may be applied in 100 litres of water per hectare although efficacy at this reduced volume has not been evaluated.

 

After treating a cereal crop with Ennobe, the following crops may be drilled after the intervals given below:

After 1 week: dwarf French beans, sunflowers, potatoes, field beans, peas, maize, oilseed rape, carrots, onions, lettuce, barley, oats, wheat.

After 4 weeks: clover, rye-grass

 

Apply as a MEDIUM spray, as defined by BCPC.

Half fill the spray tank with clean water and start the agitation. SHAKE THE CONTAINER WELL before use and pour in the required amount of product. Rinse any empty containers thoroughly and add rinsings to the spray tank. Add the remainder of the water and continue agitation until spraying is completed.

When tank mixes are to be used, each product should be added separately to the spray tank, taking due note of any instructions given as to the order of mixing.

 

For details of compatibilities contact your distributor, local BASF representative or the BASF Technical Services Hotline: 0044 845 602 2553.