Amtide Imidacloprid 2F InsecticidePlant Protection Product ComparisonPlant Protection Product ComparisonReport inaccuraciesReport inaccuracies

RESTRICTIONS
DO NOT graze treated areas or use clippings from treated areas for feed or forage. Avoid runoff or puddling of irrigation water following application. Keep children and pets off treated area until dry. Do not apply AmTide Imidacloprid 2F T&O to areas which are water logged or saturated, which will not allow penetration into the root zone of the plant. DO NOT apply more than 1.6 pt (0.4 Ib of active ingredient) per acre per year. Do not apply this product, by any application method, to linden, basswood or other Tilia species in the State of Oregon.
Treated areas may be replanted with any crop specified on an Imidacloprid label, or with any crop for which a tolerance exists for the active ingredient. For crops not listed on an Imidacloprid label, or for crops for which no tolerances for the active ingredient have been established, there is a 12-month plant-back interval.

APPLICATION INSTRUCTIONS
SHAKE WELL BEFORE USING
Direct applications of AmTide Imidacloprid 2F T&O into the seed or root-zone of crop. Failure to place this product into root-zone may result in loss of control or delay in onset of activity. This product may be applied with ground or chemigation application. Do not apply with aerial application equipment. Broadcast, foliarapplications are only recommended to seedling flats or trays, or where product is intended to be washed from foliage to soil prior to drying on foliage.Optimum activity results from applications to the root-zone of plants to be protected. The earlier this product is available to a developing plant, the earlier the protection begins. This product is continuously taken into the roots over a long period of time and the systemic nature of this product allows movement from roots through the xylem tissue to all vegetative parts of the plant. This results in extended residual activity, the control of insects and the prevention and/or reduction of virus transmission or symptom expression, and plant health benefits. The rate applied affects the length of the plant protection period. Use the higher rate specified when infestations occur later in crop development, or where pest pressure is continuous. This product will generally not control insects infesting flowers, blooms or fruit. Additional crop protection may be required for insects feeding in, or on these plant parts and for insects not listed in the crop-specific, pests controlled sections of this label. Suppression or less than complete control of certain diseases and insect pests including reduced feeding may also result from applications of this product. Complete control of these pests/diseases may require supplemental control measures. Do not use AmTide Imidacloprid 2F T&O on crops grown for production of true seed intended for private or commercial planting unless allowed under state-specific, 24(c) labeling. As with any insecticide, care should be taken to minimize exposure of the product to honey bees and other pollinators. Additional information on AmTide Imidacloprid 2F T&O uses. for these crops and other questions may be obtained from the Cooperative Extension Service, PCAs, consultants or local AmTide, LLC representatives. Pre-mix this product with water or other appropriate diluent prior to application. Keep this product and water suspension agitated to avoid settling.Do not apply more than 0.4 Ib active ingredient per acre, per year, regardless of formulation or method of application, unless specified within a crop-specific Application sections.

Mixing Instructions
To prepare the application mixture, add a portion of the required amount of water to the tank and with agitation add AmTide Imidacloprid 2F T&O. Complete filling tank with balance of water needed. Maintain sufficient agitation during both mixing and application. This product may also be used with other pesticides and/or fertilizer solutions. Please see Compatibility Note below. When tank mixtures of AmTide Imidacloprid 2F T&O and other pesticides are involved, prepare the tank mixture as specified above and follow suggested Mixing Order below.

Mixing Order
When pesticide mixtures are needed, add wettable powders first, then this product and other flowable (suspension concentrate) products second, and emulsifiable concentrates last. Ensure good agitation as each component is added. Do not add an additional component until the previous is thoroughly mixed. If a fertilizer solution is added, a fertilizer/pesticide compatibility agent may be needed. Maintain constant agitation during both mixing and application to ensure uniformity of spray mixture.

Compatibility Note
Test compatibility of the intended mixture before adding this product to the spray or mix tank. Add proportionate amounts of each ingredient in the appropriate order, to a pint or quart jar, cap, shake for 5 minutes, and let set for 5 minutes. Poor mixing or formation of precipitates that do not readily redisperse indicates an incompatible mixture that should not be used. For further information, contact your local AmTide, LLC representative.