Aura 2FPlant Protection Product ComparisonPlant Protection Product ComparisonReport inaccuraciesReport inaccuracies

DIRECTIONS FOR USE
It is a violation of Federal Law to use this product in a manner inconsistent with its labeling. See individual crops for specific pollinator application restrictions. If none exist under the specific crop, for outdoor foliar applications, follow these application directions for crops that are contracted to have pollinator services or food/feed crops and commercially grown ornamentals that are attractive to pollinators

APPLICATION INFORMATION
For best control, direct applications of Aura 2 F Insecticide into the seed or root-zone of crop. Failure to place Aura 2 F Insecticide into root-zone may result in loss of control or delay in onset of activity. Aura 2 F Insecticide may be applied by ground or chemigation. Do not apply by air. Broadcast, foliar applications are only allowed to seedling flats or trays, or where product is intended to be washed from foliage to soil before drying on foliage. For best results, apply Aura 2 F Insecticide to the root-zone of plants to be protected. Since Aura 2 F Insecticide is continuously taken into the roots over a long period of time, the earlier Aura 2 F Insecticide is available to a developing plant, the earlier the protection begins. The systemic nature of Aura 2 F Insecticide allows movement from roots through the xylem tissue to all vegetative parts of the plant. This results in extended residual activity of Aura 2 F Insecticide, the control of insects and the prevention and/or reduction of virus transmission or symptom expression, and plant health benefits. The rate of Aura 2 F Insecticide applied affects the length of the plant protection period. Use higher rates within the labeled rate range when infestations occur later in crop development, or where pest pressure is continuous. Aura 2 F Insecticide will generally not control insects infesting flowers, blooms or fruit, and additional crop protection may be required for insects feeding in or on these plant parts and for insects not listed in the cropspecific, pests controlled sections of this label.
Suppression or less than complete control of certain diseases and insect pests including reduced feeding may also be caused by an Aura 2 F Insecticide application. In such cases, pests/diseases may require supplemental control measures.
Unless allowed by State specific 24(c) labeling, the use of Aura 2 F Insecticide on crops grown for production of true seed intended for private or commercial planting is not allowed. Additional information on Aura 2 F Insecticide uses for these crops and other questions may be obtained from the Cooperative Extension Service, PCAs, consultants or local United Phosphorus, Inc. representatives.

Mixing Instructions
To prepare the application mixture, first add a portion of the required amount of water to the tank and then acid Aura 2 F Insecticide while agitation is underway. Add the remainder of water needed. Agitate during both mixing and application. Aura 2 F Insecticide may also be used with other pesticides and/or fertilizer solutions. Please see Compatibility Instructions below. When tank mixtures of Aura 2 F Insecticide and other pesticides are involved, prepare the tank mixture as described above and follow suggested Mixing Order below.

Mixing Order
When making pesticide mixtures, add wettable powders or wettable granules first, Aura 2 F
Insecticide and other suspension concentrate (flowable) products second, and emulsifiable concentrates last. Agitate as each component is added. Do not add an additional component until the previous one is thoroughly mixed. If a fertilizer solution is added, a fertilizer/pesticide compatibility agent may be needed. To ensure a uniform spray mixture, continuous agitation is necessary during both mixing and application.

Compatibility Instructions
Test the compatibility of any intended mixture before adding Aura 2 F Insecticide to the spray or mix tank. To do this, add proportionate amounts of each ingredient in the appropriate order, to a suitable size jar, cap, shake the mixture for 5 minutes, and let set for 5 minutes. Do not use the mixture if the mixing is poor, or there is formation of precipitates that do not readily redisperse. For further information, contact your local United Phosphorus, Inc. representative.