Basic Copper 50 HBPlant Protection Product ComparisonPlant Protection Product ComparisonReport inaccuraciesReport inaccuracies

GENERAL INSTRUCTIONS
Use BASIC COPPER SOW HB as noted below. BASIC COPPER SOW HB is adaptable to spraying from all types of spray equipment. Depending on the equipment used and the specific crop, tne volume applied per acre will differ. For dilute, high volume sprays use from 25 to 100 gallons of water per acre for mostvegetable crops, 400 to 800 GPA for fruit and nut crops, and up to 1500 gallons per acre as may be required for large citrus groves. For aerial spraying, 3 to 15 GPA are commonly used. For concentrate ground sprays, apply from 5 to 20 gallons per acre for vegetable crops and 25 to 100 gallons per acre for fruit and nut crops.
Add BASIC COPPER SOW HB slowly to spray tank partially filled with water. Spreader-stickers, insecticides, nutrients, etc. should be added last. BASIC COPPER SOW HB is compatible with most commercially formulated spreader-stickers, oils and other fungicides. Observe all cautions and limitations on label of all products used in mixtures.
Basic Copper 50W HB should not be applied in a spray solution having a pH of less than 6.5 to minimize phytotoxicity risk.
Basic Copper 50WP HB may be reactive on masonary and metal surfaces such as galvanized roofing.
Avoid contact of metal surfaces. Do not allow spry to contact cars, houses, lawn furniture, etc.
The following specific instructions are based on general applications. The recommendations of the State
Agricultural Extension Services should be closely followed as to timing, frequency, and number of sprays per season. When a range of doses are given for the use site, use the low dose when conditions are not favorable for disease development and use the high dose when conditions are favorable for disease development. Consult your State Agricultural Extension Service for guidance in determining what conditions favor diseases for the particular use site.

GENERAL CHEMIGATION INSTRUCTIONS
NOTE: Do not apply this product through any irrigation system using aluminum parts or components as damage to the system may occur. Such application is prohibited regardless of whether the irrigation system is flushed with water after use of this product.
Apply this product only through one or more of the following types of systems: sprinkler including center pivot, lateral move, end tow, side (wheel) roll, traveler, big gun, solid set, or hand move irrigation system(s) which contain no aluminum parts or components. Do not apply this product through any other type of
irrigation system.
Crop injury or lack of effectiveness can result from non-uniform distribution of treated water. If you have questions about calibration, you should contact State Extension Service specialists, equipment manufacturers or other experts. Do not connect an irrigation system (including greenhouse systems) used for pesticide application to a public water system unless the pesticide label-prescribed safety devices for public water systems are in place. A person knowledgeable of the chemigation system and responsible for its operation or under the supervision of the responsible person, shall shut the system down and make necessary adjustments should the need arise.
A. Center Pivot, Traveler, Big Gun, Motorized Lateral Move, End Tow, and Side (Wheel) Roll Irrigation
Equipment: Operate system and injection equipment at normal pressures recommended by the manufacturer of injection equipment used. Fill tank or injection equipment with water. Operate system for one complete circle for center pivot or one complete run for the other recommended eouipment, measuring time required, amount of water injected, and acreage contained in circle. Mix recommended amount of product for acreage to be covered into same amount of water used during calibration and inject into system continuously for one revolution or run, but continue to operate irrigation system until the product has been cleared from last sprinkler head. Spray mixture in the cnemical supply tank must be agitated at all times, otherwise settling and uneven application may occur.
Solid Set and Hand Move Irrigation Equipment: Determine acreage covered by sprinkler. Fill tank of injection equipment with water and adjust flow to use contents over a thirty to forty-fivo mir.ute perico. Mix desired amount of product for acreage to be covered into quantity of water used durhq calibration andoperate entire system at normal pressures recommended by the manufacturer of injection equipment used for amount of time established during calibration. Provide constant mechanical agitation in the mix tank to insure that the product will remain in suspension during the injection cycle. This product can be injected at the beginning or end of the irrigation cycle or as a separate application. Stop injection equipment after treatment is completed and continue to operate irrigation system until pesticide is cleared from last sprinkler head.