BROX-M ADVANCED is formulated as an emulsifiable concentrate containing the equivalent of 2.5 Ibs. per gallon of octanoic acid ester of bromoxynil and 2.5 Ibs. per gallon of 2-ethylhexyl ester of MCPA.
BROX-M ADVANCED is a selective postemergence herbicide for control of important broadleaf weeds infesting wheat, barley, oats, rye, flax and grass grown for sod. Optimum weed control is obtained when BROX-M ADVANCED is applied to actively growing weed seedlings. BROX-M ADVANCED is primarily a contact herbicide, therefore thorough coverage of the weed seedlings is essential for optimum control. BROX-M ADVANCED has little residual activity. Therefore subsequent flushes of weeds will not be controlled by the initial treatment. Generally crops that form a good canopy will help shade subsequent weed flushes.
Occasional transitory leaf burn may occur. The temporary leaf burn is similar to that seen with liquid fertilizer. Because the activity of BROX-M ADVANCED is mainly contact, recovery of the crop is generally rapid with no lasting effect. Frequency and amount of leaf burn may be greater when crops are stressed by abrasive winds, cool to cold evening temperatures or mechanical injury, such as that caused by hail, sleet or insect feeding. To reduce the potential for temporary leaf burn, applications should be made to dry foliage in the recommended spray volumes per acre when weather conditions are not extreme.
MIXING, LOADING AND HANDLING INSTRUCTIONS
2.5 Gallon Containers
Special care must be taken in mixing and loading this product. Hands should be placed on the container in such a way as to avoid possible drip or splash. Contact your local Albaugh representative if you have questions regarding the correct procedure for mixing and loading.
If you will handle a total of 48 gallons or more of this product per day, you must use a mechanical transfer system for all mixing and loading operations. If this product is packaged in a 30 gallon drum, you must use a mechanical transfer system which terminates in a drip-free hard coupling which may be used only with a spray or mix tank which has been fitted with a compatible coupling. If you do not presently own or have access to a mechanical transfer system with this type of coupling, contact your dealer for information on how to obtain such a system or to modify your present system. When using a mechanical transfer system, do not remove or disconnect the pump or probe from the container until the container has been emptied and rinsed. The pump or probe system must be used to rinse the empty container and to transfer the rinsate directly to the mixing or spray tank. BROX-M ADVANCED ALONE: Fill the spray tank 1/2 to 3/4 full with clean water. Begin agitation and add the specified amount of BROX-M ADVANCED. Add water to the spray tank to the desired level. mMaintain sufficient agitation to ensure a uniform spray mixture during application.
BROX-M ADVANCED may be tank-mixed with other pesticide products provided that these products are registered for use on the crop/use site to be treated. The tank mix must be used in accordance with the more restrictive pesticide label limitations and precautions. No label dosage rates may be exceeded. BROX-M ADVANCED cannot be mixed with any product containing a label prohibition against such mixing.
BROX-M ADVANCED can be applied in tank mixture with many other herbicides and insecticides registered for use on approved crops. Refer to the specific crop section for rate recommendations and other restrictions. To apply BROX-M ADVANCED in mixture with another product, fill the spray tank 1/2 to 3/4 full with clean water and begin agitation. If tank mixing with wettable powder, soluble powder, flowable or dry flowable products, add the powder or flowable product first. After the other herbicide is thoroughly mixed with water add the recommended amount of BROX-M ADVANCED and add water to the spray tank to the desired level. If tank mixing with other product types, add the BROX-M ADVANCED first before adding the other product. Always mix one product in water thoroughly before adding another product or compatibility problems may occur.
Maintain sufficient agitation while mixing and during application to ensure a uniform spray mixture. If spray mixture is allowed to remain without agitation for short periods of time, be sure to agitate until uniformly mixed before application.
If tank mixing with products other than those listed within each crop section, a compatibility test should be done to ensure satisfactory spray preparation. To test for compatibility, use a small container and mix a small amount (0.5 to 1 quart) of spray, combining all ingredients in the same ratio as the anticipated use.
If any indications of physical incompatibility develop, do not use this mixture for spraying. Indications of incompatibility usually will appear within 5 to 15 minutes after mixing. To ensure maximum crop safety and weed control, follow all cautions and limitations on this label and the labels of products'used in the tank mixture with BROX-M ADVANCED.
|Registered for cultures|