Finish 6 PROPlant Protection Product ComparisonPlant Protection Product ComparisonReport inaccuraciesReport inaccuracies

EPA # 0000264-00703-AA-0000000
States Registered: AL AR AZ FL GA KS LA MD MO MS NC NM OK SC TN TX VA WV

DIRECTIONS FOR USE
It is a violation of Federal Law to use this product in a manner inconsistent with its labeling.
Read entire label before using this product.
Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulations.

GENERAL INFORMATION
A foliar spray of FINISH 6 Pro Harvest Aid for Cotton will accelerate opening of mature cotton bolls, promote defoliation of both mature and juvenile foliage and reduce terminal regrowth. FINISH 6 Pro Harvest Aid for Cotton treatment promotes earlier harvest and enhances the potential for high quality, high yield, once-over harvest. Rainfall, stress, temperature fluctuations, residual nitrogen and yield potential can affect defoliation and/or regrowth.

SPRAY PREPARATION
Add 1/2 to 3/4 of the required amount of water to the spray tank. Start agitation. Add the required amount of FINISH 6 Pro Harvest Aid for Cotton, and the remaining amount of water. Mix only as much spray solution as can be used on the day of application. Storage and use of previous day’s spray mix may result in equipment corrosion and reduced activity.
Do not spill the concentrated product on spray equipment, or any airplane parts. ANY SPILLS SHOULD BE
IMMEDIATELY RINSED WITH PLENTY OF WATER AS FINISH 6 PRO HARVEST AID FOR COTTON IS
CORROSIVE. Use of a nurse tank is highly recommended for avoiding possible spills of concentrated formulation on spray equipment.

SPRAY DRIFT
Avoid spray drift. Do not apply when weather conditions may cause drift. Do not allow this product to drift on to non-target areas. Drift may result in illegal residues or injury to adjacent crops and vegetation, in the form of leaf yellowing and defoliation. To avoid spray drift, DO NOT apply aerially when wind speed is greater than 10 mph or during periods of temperature inversions. Use of larger droplet size will also reduce spray drift.
AVOIDING SPRAY DRIFT AT THE APPLICATION SITE IS THE RESPONSIBILITY OF THE APPLICATOR.
The interaction of many equipment-and-weather-related factors determine the potential for spray drift. The applicator is responsible for considering all these factors when making decisions.
The following drift management requirements must be followed to avoid off-target movement from aerial applications to agricultural field crops. These requirements do not apply to forestry applications, public health uses or to applications using dry formulations.
1. The distance of the outer most nozzles on the boom must not exceed 3/4 the length of the wingspan or rotor.
2. Nozzles must always point backward parallel with the air stream and never be pointed downwards more than 45 degrees.
Where states have more stringent regulations, they should be observed.

STORAGE AND DISPOSAL    
Do not contaminate water, food, or feed by storage or disposal.

STORAGE
Store between 0° to 50° C (32° to 122° F) in an area that is away from ignition sources. Avoid freezing. If freezing occurs, thaw and remix before using. Avoid contact with metals due to the corrosive properties of the formulation. If container is broken or contents have spilled, follow all precautions indicated above and clean up immediately. Before cleaning up, put on full length trousers, long sleeved shirt, protective gloves, and goggles or face shield. Soak up spill with absorbent media such as sand, earth or other suitable material and dispose of waste at an approved waste disposal facility.

USE PRECAUTION
Do not apply FINISH 6 Pro Harvest Aid for Cotton if rain is expected within 6 hours. Rainfall within 6 hours of application may reduce product performance.

RESTRICTIONS
Do not harvest cotton sooner than 7 days after a treatment with FINISH 6 Pro Harvest Aid for Cotton.
Do not apply this product through any kind of irrigation equipment.
Do not plant any food crop within 30 days after last application. Small grains planted earlier than 1 month or intercropped within the cotton crop to which FINISH 6 Pro Harvest Aid for Cotton will be applied may only be used as cover crops and may not be harvested for food or feed. FINISH 6 Pro Harvest Aid for Cotton may cause yellowing and growth inhibition of treated small grains.
In Arizona and California, any food crop can be planted 30 days after the last application. In the rest of the US, small grain or leafy vegetable crops can be planted only after 30 days, and all other food crops can be planted only after 4 months.
Do not exceed a maximum of 2.0 lb ethephon active ingredient per acre per year through combined or repeated uses of any ethephon products.
Do not exceed 0.25 lbs cyclanilide active ingredient per acre per year.

IMPORTANT: READ BEFORE USE
Read the entire Directions for Use, Conditions, Disclaimer of Warranties and Limitations of Liability before using this product. If terms are not acceptable, return the unopened product container at once.
By using this product, user or buyer accepts the following Conditions, Disclaimer of Warranties and Limitations of Liability.
CONDITIONS: The directions for use of this product are believed to be adequate and should be followed carefully. However, it is impossible to eliminate all risks associated with the use of this product. Crop injury, ineffectiveness or other unintended consequences may result because of such factors as weather conditions, presence of other materials, or the manner of use or application, all of which are beyond the control of Bayer CropScience. To the extent allowed by law, all such risks shall be assumed by the user or buyer.