DIRECTIONS FOR USE
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. READ ENTIRE LABEL BEFORE USING THIS PRODUCT. USE STRICTLY IN ACCORDANCE WITH LABEL PRECAUTIONARY STATEMENTS AND DIRECTIONS.
DO NOT apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulation.
This product controls broadleaf weeds and susceptible woody plants. This product should be used in conjunction with glyphosate or other grass herbicides when grassy weeds are present. Apply as a spray as directed in the Application Directions section of this label. This product provides control or suppression of a wide range of annual and perennial broadleaf weeds and susceptible woody species. Mix with sufficient water and apply as a foliar spray to obtain uniform coverage. Although water quantities may vary due to different types of application equipment, sufficient water must be used to provide for complete and uniform coverage. Higher water gallonage may be used if desired to improve coverage. In all cases, use the same recommended amount of this product per acre. When product is used for weed control in-crop, the growth stage of the crop must be considered.
For in-crop uses, do not mix with oil or other adjuvants unless specifically recommended on label. Use of an adjuvant may enhance weed control but may increase crop response in post-emergent applications inwheat, corn and grass seed crops. If you are not prepared to accept some degree of crop injury, do not use this product.
This product contains a low volatile ester especially prepared for use on crops and weeds where asusceptible crop in the near vicinity may be injured by a more volatile product. For best results apply this product as a water or oil spray during warm weather when young succulent weeds are actively .growing.
Application under drought conditions often will give poor results. The lower recommended rates will be satisfactory on susceptible, annual weeds. For perennial weeds and larger weeds, and conditions such as very dry areas where control is difficult, the higher recommended rates should be used.
This product contains a low volatile ester formulation of 2,4-D. Crop varieties vary in response to 2,4-D and some are easily injured. Apply this product to varieties known to be tolerant to 2,4-D. If you are uncertain concerning tolerant varieties or local use situations that may affect crop tolerance to 2,4-D, consult your seed company, State Agricultural Extension Service or qualified crop consultant for advice.
This product will kill, control or suppress the weed and brush species listed in the label booklet for this product. Some of these species may require repeat spot applications even under .ideal conditions.
Do not apply this product through any type of irrigation system.
Rotational Crop Restrictions: See crop specific directions for use.
Add % to % of the required amount of water to the spray tank. Start agitation. Add the required amount of this product and the remaining amount of water. Mix only as much spray solution as can be sprayed within four hours. Storage and use of the previous day's spray mix may result in reduced activity. Use an approved agricultural buffering agent, buffering to less than pH 7.5, if using this product in a water source greater than or equal to pH 7.5. Always buffer the water source BEFORE adding this product to the spray tank.
This product may be applied as a tankmix or in sequential application with other fungicide, insecticide or herbicide products. Weather, crop conditions, or the presence of certain weeds, crop damaging insects, or diseases will indicate the inclusion of other pesticides. Apply with grass herbicides if grassy weeds are present.
NOTE: All intended tank mix combinations should be used only in recommended areas on the same broadleaf weed species found on both labels.
For application methods and other use specifications, use the most restricted limitations from labeling of both products.
Note: It is recommended that the compatibility of this product in any tankmix combination be tested before use. To determine the physical compatibility with other products, use a jar test, as describedbelow:
Using a quart jar, add the proportionate amounts of the products to 1 qt. of water. Add wettable powders and water-dispersible granular products first,-then liquid flowables, and emulsifiable concentrates last.After thoroughly mixing, let stand for at least 5 minutes. If the combination remains mixed or can be remixed readily, it is physically compatible. Once compatibility has been proven, use the same procedure for adding required ingredients to the spray tank.
|Registered for cultures||Rate|
|Corn||0 fl oz|
|Soybeans||12 - 24 fl oz|
|Winter wheat||9 - 24 fl oz|
|Spring wheat||9 - 24 fl oz|
|Spring barley||9 - 24 fl oz|
|Winter barley||9 - 24 fl oz|
|Winter rye||9 - 24 fl oz|
|Spring rye||9 - 24 fl oz|
|Spring oats||9 - 24 fl oz|
|Winter oats||9 - 24 fl oz|