PENNCOZEB 75DFPlant Protection Product ComparisonPlant Protection Product ComparisonReport inaccuraciesReport inaccuracies

APPLICATION INSTRUCTIONS

All aerial and ground application equipment must be properly maintained and calibrated using appropriate carriers or surrogates FOR AERIAL APPLICATION use at the rate indicated in sufficient water for thorough coverage, a minimum of 2 gallons per acre for field crops and 10 gallons per acre for orchard crops Use a Spreader Sticker at rate of 4 fl oz per 100 gallons spray if needed Add product slowly to water in the spray tank with agitation, or premix thoroughly in separate holding tank for concentrate or aircraft sprayers Continuous agitation is required to keep the product in suspension

When dosage ranges are given, use the higher specified rate and shorter intervals under severe disease pressure, but do not exceed the maximum rate or apply more frequently than the minimum interval given in the directions for that crop

RESISTANCE MANAGEMENT

PENNCOZEB 75DF is an excellent disease control agent when used according to label directions for control of a broad spectrum of plant diseases PENNCOZEB 75DF is recommended for use in programs which are compatible with the principles of Integrated Pest Management (IPM) PENNCOZEB 75DF is effective for strategic use in programs that attempt to minimize disease resistance to fungicides Some other fungicides which are at risk from disease resistance exhibit a single-site mode of fungicidal action PENNCOZEB 75DF, with a multi-site mode of action, may be used in an Integrated Pest Management (IPM) program to delay or prevent the development of resistance to single-site fungicides Consult with your private crop consultant or Federal or State Cooperative Extension Service representatives for guidance on the proper use of PENNCOZEB 75DF in programs which seek to minimize the occurrence of disease resistance to other fungicides

USE INSTRUCTIONS

Apply this product only through sprinkler irrigation systems including center pivot, lateral move, end tow, side (wheel) roll, traveler, big gun, solid set, or hand move Do not apply this product through any other type of irrigation system Crop injury, lack of effectiveness, or illegal pesticide residues in the crop can result from non-uniform distribution of treated water If you have any questions about calibration, you should contact State Extension Service specialists, equipment manufacturers or other experts A person knowledgeable of the chemigation system and responsible for its operation, or under the supervision of the responsible person, shall shut the system down and make necessary adjustments should the need arise Do not connect chemigation system to any public water system Public water system means a system for the provision of piped water for human consumption if such system has at least 15 service connections or regularly serves an average of at least 25 individuals daily at least 60 days out of the year

SYSTEM REQUIREMENTS

Systems utilizing a pressurized water and pesticide injection system must meet the following requirements: The system must contain a functional check valve, vacuum relief valve, and low pressure drain appropriately located on the irrigation pipeline to prevent water source contamination from backflow The pesticide injection pipeline must contain a functional, automatic, quickclosing check valve to prevent the flow of fluid back toward the injection pump The pesticide injection pipeline must also contain a functional, normally closed, solenoid-operated valve located on the intake side of the injection pump and connected to the system interlock to prevent fluid from being withdrawn from the supply tank when the irrigation system is either automatically or manually shut down The system must contain functional interlocking controls to automatically shut off the pesticide injection pump when the water pump motor stops 4 The irrigation line or water pump must include a functional pressure switch which will stop the water pump motor when the water pressure decreases to the point where pesticide distribution is adversely affected Systems must use a metering pump, such as a positive displacement injection pump (eg, diaphragm pump) effectively designed and constructed of materials that are compatible with pesticides and capable of being fitted with a system interlock

INSTRUCTIONS FOR SPRINKLER

(OVERHEAD) IRRIGATION: Observe the requirements in the SYSTEM REQUIREMENTS section Do not apply when wind speed favors drift beyond the area intended for treatment Apply PENNCOZEB 75DF only through systems containing anti-siphon and check valves designed to prevent water source contamination or overflow of the mix tank and containing interlocking controls between the metering device and the water pump to insure simultaneous shut-off Maintain a gentle continuous agitation in mix tank during mixing and application to assure a uniform suspension Greater accuracy in calibration and distribution will be achieved by injecting a larger volume of a more dilute suspension per unit time Application of more than recommended quantities of irrigation water per acre may result in decreased product performance Do not apply when wind speed favors drift, when system connections or fittings leak, when nozzles do not provide uniform distribution or when lines containing the product cannot be flushed and must be dismantled and drained In a center pivot system, block the nozzle set nearest the well/pivot/ injection unit to prevent spray being applied to this area.