Willowood Glufosinate 280SL

Registered until
Registration number
Active materials

It is a violation of Federal law to use this product in a manner inconsistent with its labeling.
Do not use this product until you have read the entire label. Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application.
For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulation. In the State of New York Only: Not For Use In Nassau and Suffolk Counties.

Willowood Glufosinate 280SL is a water soluble herbicide for application as a foliar spray for the control of a broad spectrum of emerged annual and perennial grass and broadleaf weeds in LibertyLink canola, LibertyLink corn, LibertyLink cotton, and LibertyLink soybean, and in trees, vines, and berries. Willowood Glufosinate 280SL may be applied for potato vine desiccation. Willowood Glufosinate 280SL may also be applied as a broadcast burndown application before planting or prior to emergence of any conventional or transgenic variety of canola, sweet corn*, corn, cotton, olive, rice*, soybean, or sugar beet.
*Not for use in California.
Willowood Glufosinate 280SL is only foliar active with little or no activity in soil. Weeds that emerge after application will not be controlled. Apply Willowood Glufosinate 280SL to actively growing weeds as described in the Weed Control Recommendations for Row Crops section to get maximum weed control.
Uniform thorough spray coverage is necessary to achieve consistent weed control. Necrosis of leaves and young shoots occur within 2 to 4 days after application under good growing conditions.
• Willowood Glufosinate 280SL is rainfast four (4) hours after application to most weed species, therefore, rainfall within four (4) hours may necessitate retreatment or may result in reduced weed control.
• Application should be made between dawn and 2 hours before sunset to avoid the possibility ofreduced lambsquarters and velvetleaf control.
• Consult your local Cooperative Extension Service or Willowood, LLC Representative for guidelines on the optimum application timing for Willowood Glufosinate 280SL in your region.
• Weed control may be reduced if application is made when heavy dew, fog, and mist/rain are present, or when weeds are under stress due to environmental conditions such as drought, cool temperatures, or extended periods of cloudiness.
• To maximize weed control, do not cultivate from 5 days before an application to 7 days after an application.

Do not use flood jet nozzles, controlled droplet application equipment, or air assisted spray equipment. Uniform thorough spray coverage is important to achieve consistent weed control.

Ground Application
Refer to the Rate Tables for proper application rates. Do not apply when winds are gusty, or when conditions
will favor movement of spray particles off the desired spray target. To avoid drift and ensure consistent
weed control, apply Willowood Glufosinate 280SL with the spray boom as low as possible while maintaining
a uniform spray pattern. Willowood Glufosinate 280SL should be applied broadcast in a minimum of 10
gallons of water per acre using a minimum spray pressure of 40 psi and a maximum ground speed of 10
mph. The use of 80 degree or 110 degree flat fan nozzles is highly recommended for optimum spray
coverage and canopy penetration. Application of the spray at a 45 degree angle forward will result in better
spray coverage. Under dense weed/crop canopies a broadcast rate of 15-20 gallons of water per acre
should be used so that thorough spray coverage will be obtained. DO NOT use raindrop nozzles.
Boom height should be based on nozzle manufacturer recommendations. See the Spray Drift Management
section of this label for additional information on proper application of Willowood Glufosinate 280SL.
Aerial Application
Poor coverage will result in reduced weed control. For optimal weed control, apply Willowood Glufosinate
280SL in a minimum of 10 gallons per acre. Apply Willowood Glufosinate 280SL using nozzles and
pressures that generate MEDIUM (about 300 to 400 microns) spray droplets category as reported by the
nozzle manufacturer and in accordance to ASABE S 572 based upon the selected air speed. Do not use
nozzles and pressures that result in COARSE sprays. FINE sprays should also be avoided to minimize
spray drift risk. See the Spray Drift Management section of this label for additional information on proper
application of Willowood Glufosinate 280SL

Registered for cultures