Mpower Battlefront 50 SC

Manufacturer
NewAgco
Category
Herbicides
Registered until
2027-12-31
Registration number
31325
Active materials
Links

MPOWER FLORASULAM HERBICIDE is a selective herbicide for postemergent control or suppression of annual broadleaf weeds including cleavers, wild buckwheat and chickweed in spring wheat (including durum), spring barley, and oats (tank mixes only).

GENERAL INFORMATION


MPOWER FLORASULAM HERBICIDE is a selective postemergence herbicide for the control or suppression of hard-to-kill annual broadleaf weeds such as chickweed, wild buckwheat and cleavers in spring wheat (including durum), spring barley, and oats (tank mixes only) not underseeded with legumes. MPOWER
FLORASULAM HERBICIDE is mixed with water and applied as a uniform broadcast spray. It is non-corrosive, nonflammable, and nonvolatile.
MPOWER FLORASULAM HERBICIDE must be applied early postemergence, to the main flush of actively growing broadleaf weeds. Warm, moist growing conditions promote active weed growth and enhance the activity of MPOWER FLORASULAM HERBICIDE by allowing maximum foliar uptake and contact activity.
Weeds hardened off by cold weather or drought stress may not be adequately controlled or suppressed and re-growth may occur. For best results, ensure thorough spray coverage of target weeds. See “DIRECTIONS FOR USE” section of this label for complete use details.
MPOWER FLORASULAM HERBICIDE stops growth of susceptible weeds rapidly. However, typical symptoms (discolouration) of dying weeds may not be noticeable for 1 to 2 weeks after application, depending upon growing conditions and weed susceptibility. Degree of control and duration of effect are dependent on weed sensitivity, weed size, crop competition, growing conditions at and following treatment, and spray coverage.

MODE OF ACTION


MPOWER FLORASULAM HERBICIDE inhibits the production of the ALS enzyme in plants. This enzyme is essential for the production of certain amino acids which are essential for plant growth. MPOWER FLORASULAM HERBICIDE is a Group 2 mode of action herbicide.

GENERAL DIRECTIONS FOR USE


READ THE ENTIRE LABEL BEFORE USE. FAILURE TO FOLLOW LABEL INSTRUCTIONS MAY
RESULT IN ERRATIC WEED CONTROL OR CROP DAMAGE.
DO NOT APPLY TO CROPS UNDERSEEDED WITH LEGUMES.
As this product is not registered for the control of pests in aquatic systems, DO NOT use to control aquatic pests.
DO NOT contaminate irrigation or drinking water supplies or aquatic habitats by cleaning of equipment or disposal of wastes.
Field sprayer application: DO NOT apply during periods of dead calm. Avoid application of this product when winds are gusty. DO NOT apply with spray droplets smaller than the American Society of Agricultural
Engineers (ASAE S572.1) medium classification. Boom height must be 60 cm or less above the crop or ground.
Aerial application: DO NOT apply using aerial application equipment.

Application Directions
Apply 100 mL of MPOWER FLORASULAM HERBICIDE per hectare in a minimum of 100 L per hectare of water. Add Agral 90 at 0.2% v/v. See weeds species controlled under “Weeds Controlled or Suppressed by
MPOWER FLORASULAM HERBICIDE Alone at 100 mL/ha.”
Apply to actively growing wheat and barley from the 2 to 6 leaf stage. Apply when weeds are actively growing.
Only weeds emerged at the time of treatment will be controlled. Best results are obtained from applications made to seedling weeds.

Application Timing
Apply to actively growing weeds in the 2-4 leaf stage. Extreme growing conditions such as drought or near freezing temperature prior to, at or following time of application may reduce weed control and increase the risk of crop injury at all stages of growth. Only weeds which are emerged at the time of application will be affected. If foliage is wet at the time of application control may be decreased. Under conditions of low crop and high weed density, control may be reduced.

Registered for culturesRate
Spring wheat230 - 290 ml
Durum Wheat230 - 290 ml