Mpower Pro
- Manufacturer
- NewAgco
- Category
- Herbicides
- Registered until
- 2024-12-31
- Registration number
- 31118
- Active materials
- metsulfuron-methyl600 g/l
- Links
- LabelView
DIRECTIONS FOR USE:
IMPORTANT
Injury to or loss of desirable trees or vegetation may result from failure to observe the following. Do not apply, drain or flush equipment on or near desirable trees or other plants, or on areas where their roots may extend, or in locations where the chemical may be washed or moved into contact with their roots. Do not use on lawns, walks, driveways, tennis courts or similar areas. Prevent drift of spray to desirable plants. Do not contaminate any body of water, including irrigation water that may be used on other crops.
APPLY MPOWER PRO WITH RECOMMENDED SURFACTANT.
DO NOT APPLY BY AIR.
Carefully observe sprayer clean-up instructions, as spray tank residue may damage crops other than wheat, barley or creeping red fescue.
PRIOR TO USE REFER TO “MINIMUM CROP ROTATION GUIDELINES” SECTION OF LABEL.
GENERAL INFORMATION
MPOWER PRO is recommended for postemergence use on wheat (spring and durum), barley and established creeping red fescue, orchard grass, crested and intermediate wheat grass (seed or forage) in the
Prairie Provinces and the Peace River Region of British Columbia (soil pH of 7.9 or lower). In addition, MPOWER PRO is recommended for use on pasture and rangeland in the same geographic region (no soil pH restriction).
MPOWER PRO is to be mixed in water with a recommended surfactant and applied as a uniform broadcast spray. Use for selective control or suppression of certain broadleaf weeds in spring wheat (including durum), barley and established creeping red fescue (seed or forage) and for control of Western Snowberry and Wild
Rose in pasture and rangeland. MPOWER PRO is non-corrosive, non-flammable, non-volatile and does not freeze. Wheat, barley or creeping red fescue may be grazed by or fed to livestock anytime after treatment.
MPOWER PRO is a 60% active ingredient herbicide formulated as water dispersible granules.
Prior to using MPOWER PRO, careful consideration should be given to crop rotation plans. Crops other than those listed in the “Minimum Crop Rotation Guidelines” section can be very sensitive to low concentrations of MPOWER PRO in the soil. Refer to the “Minimum Crop Rotation Guidelines” section of this label to plan your MPOWER PRO use and crop rotations.
Rainfall, soil temperature and soil pH are important factors affecting MPOWER PRO breakdown in the soil.
MPOWER PRO breakdown is more rapid under conditions of moist soil, warm soil temperatures and low soil pH. The breakdown process is slower under conditions of dry soil, cool soil temperatures and high soil pH.
MPOWER PRO must be applied with a recommended surfactant early postemergence to the main flush of actively growing broadleaf weeds. For pasture and rangeland applications, MPOWER PRO should be applied bet ween mid-June and mid-August after the target species have leafed out, but before fall colouration begins. Cattle may graze the treated areas on the day of treatment.
Warm, moist growing conditions promote active weed growth and enhance the activity of MPOWER PRO by allowing maximum foliar uptake and contact activity. If cold, dry conditions prevail, delay treatment until active weed growth resumes. Weeds hardened off by cold weather or drought stress may not be adequately controlled or suppressed and re-growth may occur. MPOWER PRO may only be applied with ground spray equipment. For best results, ensure good spray coverage of target weeds.
MPOWER PRO rapidly inhibits the growth of susceptible weeds, however, typical symptoms (discolouration) of dying weeds may not be noticeable for 1 to 3 weeks after application depending upon growing conditions and weed susceptibility. Degree of control and duration of effect depend on weed sensitivity, weed size, growing conditions, soil pH and spray coverage.
HOW TO APPLY TO WHEAT (SPRING OR DURUM), BARLEY OR ESTABLISHED CREEPING RED FESCUE (SEED OR FORAGE)
Apply MPOWER PRO or MPOWER PRO tank mixtures to the first main flush of actively growing weeds, when the crop is in the leaf stage specified in the section CROP STAGE. Apply before the crop canopy is dense enough to prevent thorough coverage of the weeds. Apply with ground equipment only. Make only one application per growing season. For further information on control of Canada thistle, sow thistle, Russian thistle, lamb’s quarters or wild buckwheat, refer to the section SPECIFIC WEED CONTROL RECOMMENDATIONS.
DO NOT APPLY BY AIR.
Registered for cultures | Rate |
---|---|
Spring wheat | 7.5 g |
Durum Wheat | 7.5 g |