Clincher CAPlant Protection Product ComparisonPlant Protection Product ComparisonReport inaccuraciesReport inaccuracies

Registratration Number: 62719-356
States available in: AL AK AZ AR CA CO CT DE FL GA HI ID IL IN IA KS KY LA ME MD MA MI MN MS MO MT NE NV NH NJ NM NC ND OH OK OR PA RI SC SD TN TX UT VT VA WA WV WI WY

Agricultural Use Requirements
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR Part 170. Refer to label booklet under "Agricultural Use Requirements" in the Directions for Use section for information about this standard.

User Safety Recommendations
Users should:
Wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet.
Remove clothing immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing.
Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing.

Agricultural Use Requirements
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR Part 170. This Standard contains requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training, decontamination, notification, and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this label about personal protective equipment (PPE), and restricted entry interval. The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard. Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 12 hours.

Storage and Disposal
Do not contaminate water, food or feed by storage and disposal.
Pesticide Storage: Store in cool dry place in original container.
Pesticide Disposal: Wastes resulting from the use of this product must be disposed of on site or at an approved waste disposal facility.
Nonreflllable containers 5 gallons or less:
Container Reuse: Nonreflllable container. Do not reuse or reflll this container. Offer for recycling if available. Triple rinse or pressure rinse container (or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the fiow begins to drip. Fill the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the fiow begins to drip. Repeat this procedure two more times. Pressure rinse as follows: Empty the remaining contents into application equipment or a mix tank and continue to drain for 10 seconds after the fiow begins to drip. Hold container upside down over application equipment or mix tank or collect rinsate for later use or disposal. Insert pressure rinsing nozzle in the side of the container, and rinse at about 40 psi for at least 30 seconds. Drain for 10 seconds after the fiow begins to drip.
Reflllable containers 5 gallons or larger:
Container Reuse:
Reflllable container. Reflll this container with pesticide only. Do not reuse this container for any other purpose. Cleaning the container before flnal disposal is the responsibility of the person disposing of the container. Cleaning before refllling is the responsibility of the reflller. To clean the container before flnal disposal, empty the remaining contents from this container into application equipment or a mix tank. Fill the container about 10% full with water and, if possible, spray all sides while adding water. If practical, agitate vigorously or recirculate water with the pump for two minutes. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this rinsing procedure two more times.
Nonreflllable containers 5 gallons or larger:
Container Reuse:
Nonreflllable container. Do not reuse or reflll this container. Offer for recycling if available. Triple rinse or pressure rinse container (or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container 1/4 full with water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensuring at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty the rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this procedure two more times. Pressure rinse as follows: Empty the remaining contents into application equipment or a mix tank and continue to drain for 10 seconds after the fiow begins to drip. Hold container upside down over application equipment or mix tank or collect rinsate for later use or disposal. Insert pressure rinsing nozzle in the side of the container, and rinse at about 40 psi for at least 30 seconds. Drain for 10 seconds after the fiow begins to drip.

Mixing Instructions
Use of Surfactants
Use of an agriculturally approved crop oil concentrate at a rate of 2.5% v/v must be used for all applications of Clincher CA. Read and follow all use directions and precautions on crop oil concentrate label.
Clincher CA - Alone
Fill spray tank to one-half (1/2) full with water. Start agitation. Add required quantity of Clincher CA and crop oil concentrate. Continue agitation while fllling spray tank to required volume and during application.
Clincher CA in Tank Mix
Continuous agitation is required for tank mixes. Sparger pipe agitators generally provide the best agitation in spray tanks. Mixing Order: Fill the tank one-third (1/3) full with water. Start the agitation. Different formulation types should be added in the following order: dry fiowables (DF), wettable powders (WP), aqueous suspensions (AS), fiowables (F), or liquids (L). Allow each product type to completely disperse before adding another. Continue agitation and flll the spray tank to three-fourths (3/4) full, add the correct quantity of Clincher CA or other emulsiflable concentrates (EC) and mix thoroughly. Finally, add any solution (S) formulations or surfactant, agitate and flnish fllling. Maintain agitation during fllling and during application. If spraying and agitation must be stopped before the tank is empty, suspended materials may settle to the bottom. It is important to resuspend all of the settled material before continuing application. A sparger agitator is particularly useful for this purpose.
Carefully follow all mixing instructions for each material added to the tank. Initial dispersion of dry or fiowable formulations can be improved by mixing with a small amount of water (slurrying) and pouring the slurry through a 20 to 35 mesh wetting screen in the top of the spray tank. Line screens in the tank should be no flner than 50 mesh (100 mesh is flner than 50 mesh).

Active