F9210-1

Manufacturer
FMC
Category
Insecticides
Registered until
Registration expired
Registration number
279-3440
Active materials
Links

APPLICATION INSTRUCTIONS
F9210-1 is a suspoemulsion formulation containing three active ingredients from insecticide classes 3 and 4A. F9210-1 can be applied by air, ground and through chemigation equipment as a directed or broadcast foliar spray or unless otherwise noted in specific crop sections in this label. F9210-1 may be applied before or after planting for control of cutworm, armyworm or stalkborer. Spray gallonage minimum amounts for each crop are listed in each specific crop section for aerial and ground applications. Chemigation instructions are found in the chemigation section of this label. In general, use lower listed rates under light and moderate infestations. Higher listed rates should be used under heavy crop canopy or insect pressure. The rate of application is variable according to insect pressure, timing of spray, plant foliage and field scouting. Thorough coverage of foliage is necessary without runoff for optimum insecticidal efficacy.

RESTRICTIONS FOR ALL USES:
Do not use in enclosed structures, including greenhouses or planthouses In New York State this product may not be applied within 100 feet (using ground equipment) or 300 feet (using aerial equipment) of coastal marshes or streams that drain into coastal marshes.The maximum amount of Imidacloprid that can be applied per acre is 0.5 Ib Al per year for this product or any additional products containing Imidacloprid.

Chemigation Use Directions
Apply this product only through.overhead sprinkler system including center pivot, lateral move, end tow, side (wheel) roll, traveler, big gun, solid set, or hand move irrigation systems. Do not apply this product through any other type of irrigation system. Do not connect any irrigation system (including greenhouse systems) used for pesticide application to a public water system. Crop injury, lack of effectiveness, or illegal residues in the crop can result from non-uniform distribution of treated water. If you have questions about calibration, you should contact State Extension Service specialists, equipment manufacturers, or other experts. A person knowledgeable of the chemigation system and responsible for its operation, or under the supervision of the responsible person, shall shut the system down and make necessary adjustments should the need arise. The system must contain a functional check valve, vacuum relief valve, and low-pressure drain appropriately located on the irrigation pipeline to prevent water source contamination from backflow. The pesticide injection pipeline must also contain a functional, automatic, quick-closing check valve to prevent the flow of fluid back toward the injection pump. The pesticide injection pipeline must also contain a functional, normally closed, solenoid-operated valve located on the intake side of the injection pump and connected to the system interlock to prevent fluid from being withdrawn from the supply tank when the irrigation system is either automatically or manually shut down. The system must contain functional interlocking controls to automatically shut off the pesticide injection pump when the water pump motor stops. The irrigation line or water pump must include a functional pressure switch that will stop the water pump motor when the water pressure decreases to the point where pesticide distribution is adversely affected. Systems must use a metering pump, such as a positive displacement injection pump (e.g., diaphragm pump) effectively designed and constructed of materials that are compatible with pesticides and capable of being fitted with a system interlock. Do not apply when wind speed favors drift beyond the area intended for treatment. F921Q-1 should be applied continuously for the duration of the water application. F9210- 1 should be diluted in sufficient volume to insure accurate application over the area to-be treated. Use the appropriate amount of water to carry the product to the target pest. Agitation is not required when a suitable diluent is used. Chemigation ofF9210-1 in water volumes exceeding 0.10 inches/Acre are not recommended.

Tank-Mixture
F9210-1 may be applied in tank mixtures with other products approved for use on crops on this label. Test for compatibility of products before mixing.

Rotational Crops
Crops on this label, or for which imidacloprid, bifenthrin, and zeta-cypermethrin tolerances exist may be rotated immediately. All other crops, except cereals (including buckwheat, millet, oats, rice, rye and triticale), onion and bulb vegetables maybe rotated 12 months after the final application of F9210-1. Cereals, including buckwheat, millet, oats, rice, rye and triticale, maybe rotated 30 days and onion and bulb vegetables maybe be rotated 10 months after the final application of F9210-1.

Registered for cultures
Cotton
Potatoes
Soybeans
Broccoli
Lettuce
Peas
Beans
Peppers
Okra
Tomatoes
Grapes
Citrus