2,4-D LV Ester 680

Manufacturer
ADAMA
Category
Herbicides
Registered until
2024-06-30
Registration number
61895
Active materials
Links

GROUP I HERBICIDE

A specially formulated low volatile herbicide for selective control of various weeds in crops, pastures and non-agricultural areas as specified in the Directions for Use table.
This is a PHENOXY HERBICIDE that can cause severe damage to susceptible crops such as cotton, grapes, tomatoes, oilseed crops and ornamentals.

DIRECTIONS FOR USE:
Restraints:
AVOID spraying if rain is likely within 6 hours or if strong winds prevail.
DO NOT apply if crop or weeds are stressed due to dry or excessively moist conditions.
DO NOT use when breeze is blowing towards nearby susceptible plants

WHEAT, BARLEY
Weeds controlled: Refer to Weed Table
State: Vic only
Rate / ha: 210-800 mL
State: SA only
Rate / ha: 230-800 mL
State: Qld, NSW, ACT only
Rate / ha: 410-800 mL
State: Tas only
Rate / ha: 620-800 mL
State: WA only
Rate / ha: 800 mL

TRITICALE
Weeds controlled: Refer to Weed Table
State: Qld, NSW, ACT only
Rate / ha: 410-800 mL
State: SA only
Rate / ha: 240-820 mL
State: Vic only
Rate / ha: 210-800 mL

CEREAL RYE
Weeds controlled: Refer to Weed Table
State: Qld, NSW, ACT only
Rate / ha: 410-800 mL
State: Vic only
Rate / ha: 210-800 mL

Critical comments: CROP STAGES: ALL CEREALS
Variations between varieties do occur. Check sensitivity and growth stages of varieties before spraying. Damage may result if applied too early.
Vic only: Apply at tillered to boot stages.
NSW, ACT only: Apply after when the first node can be felt at the base of a tiller and before swelling of the head can be felt in a tiller.
Qld only: Apply from mid-tillering (5 to 6 fully emerged main stem leaves plus one or more tillers) to before boot stage (visible swelling of the head at the top of the main stem).
SA, Tas only: Apply from completion of tillering to early jointing stage.
WA only: Apply from the 5 leaf stage up to jointing stage (Zadoks 15-33). Apply only at 6 leaf stage for Cranbrook and Jacup
wheats (Zadoks 16) to avoid possible damage.

SUGARCANE
Weeds controlled: Refer to Weed Table
State: Qld only
Rate / ha: 1.15-2.4 L
Critical comments: Post-emergence.

Stubble/Fallow Spray prior to direct drilling or sowing.
WINTER CEREALS, GRAIN LEGUMES (PEANUTS, QLD ONLY), CANOLA
Weeds controlled: Refer to Weed Table
State: All States
Rate / ha: 210-800 mL
Critical comments: Observe the plant back periods given in the table in this leaflet. Must be tank mixed with a knockdown herbicide such as Trifluralin 480, Wipe-Out® CT Elite, Spraytop® 250 or Spray-Seed†. Select appropriate rate from the weed table.
For Skeleton Weed, spraying should only be done 6-8 weeks before anticipated sowing date and subsequent cultivation limited to a minimum.

Harvest aid or salvage spray
WINTER CEREALS
Weeds controlled: Broadleaf Weeds, Refer to Weed Table
State: All States
Rate / ha: 1.7 L
Critical comments: Apply after dough stage of crop. Interval between application and effectiveness is 10-20 days. For dessication of green matter, estimate harvest date and apply spray approximately 14 days earlier. Rain between spraying and actual harvest can negate results.
Note: Where thistles are tall and branching above the crop, spraying can turn the branches down into the crop, presenting more stalks to cause header comb blockages. Spraying may increase seed contamination of harvest by accelerating maturity. DO NOT use with undersown legumes that have not set seed.

POTATOES
Pre-Harvest Preparation

Weeds controlled: Broadleaf Weeds such as Clover, Variegated Thistle & Cruciferous weeds
State: Vic, Tas only
Rate / ha: 1.15-2.4 L
Critical comments: Apply approximately 4 to 5 weeks before harvest after the potato haulms have dried off. Use the highest rate where weeds are more than 30 cm in height. For boom spraying apply at least 100 litres of spray mixture per hectare. If grasses such as Rye Grass and Winter Grass are also present add Amitrole T Herbicide.

PASTURE
Improved Pasture containing Clovers
Weeds controlled: Refer to Weed Table
State: Qld, NSW, ACT, Tas, SA only
Rate / ha: 410-800 mL
Critical comments: Clover must be well covered by the grass or extensive damage may result.

PASTURE - non legumes, Rights of Way and Industrial
Weeds controlled: Refer to Weed Table
State: Qld, NSW, ACT, Tas, SA, WA only
Rate / ha: 800 mL-4.7 L
Critical comments: Control of most perennial weeds, but due to the rooting habits of most species control may take a number of years. Damage may result to legumes in pasture.
State: Vic only
Rate / ha:
Boom spray: 800 mL-6.6 L
Spot spraying: 70-620 mL/100 L

PASTURE – Direct Drilling or Surface Sowing
Weeds controlled: Charlock, Clover, Medics, Mustards, Paterson’s Curse, Saffron, Slender, Variegated and Spear Thistles, Turnip Weed, Wild Radish, Wild Turnip
State: Qld, NSW, ACT, Vic, Tas, SA, WA only
Rate / ha: 800 mL-1.5 L (aerial application)

Weeds controlled: As above plus: Capeweed, Wireweed, Storksbill/Erodium, Flatweed, Horehound (seedlings), Skeleton Weed, Nodding or Star Thistles
State: Qld, NSW, ACT, Vic, Tas, SA, WA only
Rate / ha: 800 mL-1.15 L (ground application)

Weeds controlled: St Johns Wort
State: Qld, NSW, ACT, Vic, Tas, SA, WA only
Rate / ha: 3.3-4.7 L (aerial or ground)

Weeds controlled: All of the above plus grasses
State: Qld, NSW, ACT, Vic, Tas, SA, WA only
Rate / ha: As above plus Wipe-Out CT, Wipe-Out 360, Trifluralin 480 or Propon)

Critical comments: Apply to young, actively growing weeds.
SOWING: DO NOT sow pasture seed for at least 21 days after application.
If soil moisture is dry, delay sowing for at least 30 days.

NOT TO BE USED FOR ANY PURPOSE, OR IN ANY MANNER, CONTRARY TO THIS LABEL UNLESS AUTHORISED UNDER APPROPRIATE LEGISLATION.

IN TASMANIA, THIS PRODUCT MAY ONLY BE USED FROM 15TH APRIL TO 15TH SEPTEMBER UNLESS OTHERWISE PERMITTED BY THE REGISTRAR OF PESTICIDES.

WITHHOLDING PERIODS (WHP):
PASTURES, CEREAL CROPS: DO NOT GRAZE OR CUT FOR STOCK FOOD FOR 7 DAYS AFTER APPLICATION.
HARVEST WITHHOLDING PERIOD: NOT REQUIRED WHEN USED AS DIRECTED.

WEED TABLE
Note: Where weeds are to be sprayed in a CROP or PASTURE, use only the rates given for the crop in the table below. In most cases this will give control, however some hard to kill weeds or those in advanced stages of growth may only be suppressed, eg. Rumex spp. (Docks) and Polygonum spp. (Wireweed, Climbing Buckwheat) are killed to ground level only.

Weeds controlled: Amaranthus spp.
Application rate per hectare:
Crop:
NSW, ACT: 800 mL

Weeds controlled: Angled Onion
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3 L
NSW, TAS, SA, QLD, WA ONLY: 0.8-1.7 L
Critical comments: Spray when buds forming or early flowering.

Weeds controlled: Apple of Sodom
Application rate per hectare:
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 2.9-3.3 L

Weeds controlled: Bathurst Burr
Application rate per hectare:
Crop:
NSW, ACT: 800 mL
Pastures - non legumes:
Vic: 1.7-3.3 L
NSW, TAS, SA, QLD, WA ONLY: 1.7-3.3 L
Critical comments: Spray from seedling to pre-flowering. Use higher rate as plant matures.

Weeds controlled: Black Knapweed
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3 L
Critical comments: Spray before flowering. DO NOT cultivate these infestations.

Weeds controlled: Buffalo Burr
Application rate per hectare:
Pastures - non legumes:
NSW, TAS, SA ONLY: 800 mL-1.15 L
Critical comments: Spray from seedling to pre-flowering. Use higher rate as plant matures.

Weeds controlled: California Burr
Application rate per hectare:
Crop:
NSW, ACT: 800 mL
Pastures - non legumes:
Vic: 1.7-3.3 L
NSW, TAS, QLD, WA ONLY: 1.15-1.7 L
Critical comments: Spray from seedling to pre-flowering. Use higher rate as plant matures.

Weeds controlled: Cape Tulip
Application rate per hectare:
Crop:
WA: 1.15 L
Pastures - non legumes:
Vic: 3.3 L
NSW, TAS, SA, QLD, WA ONLY: 1.7-3.3 L
Critical comments: Spray before flowering.

Weeds controlled: Capeweed
Application rate per hectare:
Crop:
Vic: 800 mL
SA: 800 mL
TAS: 800 mL
NSW, ACT: 530-800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 2.5-3.3 L
Critical comments: Spray up to rosette stage.

Weeds controlled: Charlock
Application rate per hectare:
Crop:
Vic: 410 mL
NSW, ACT: 410 mL
SA: 410 mL
Tas: 800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 800 mL
Critical comments: Spray up to rosette stage.

Weeds controlled: Clover
Application rate per hectare:
Crop:
NSW, ACT: 620-800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 800 mL

Weeds controlled: Colocynth
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3 L
Critical comments: Spray at seedling stage only.

Weeds controlled: Deadnettle
Application rate per hectare:
Crop:
NSW, ACT: 800 mL

Weeds controlled: Devil’s Claw
Application rate per hectare:
Crop:
NSW, ACT: 800 mL
Pastures - non legumes:
Vic: 1.3 L
NSW, TAS, QLD, WA ONLY: 1.15-1.7 L
Critical comments: Spray prior to pods forming.

Weeds controlled: Docks
Application rate per hectare:
Crop:
Vic: 800 mL
SA: 800 mL
Qld: 800 mL
WA: 800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 1.7-2.5 L
Critical comments: Spray at rosette stage to kill top growth only.

Weeds controlled: Fat Hen
Application rate per hectare:
Crop:
NSW, ACT: 410-800 mL

Weeds controlled: Flat Weed
Application rate per hectare:
Crop:
NSW, ACT: 800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 2.5-3.3 L

Weeds controlled: Fumitory – red
Application rate per hectare:
Crop:
SA: 800 mL
NSW, ACT: 800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 2.5-3.3 L
Critical comments: Spray up to rosette stage.

Weeds controlled: Fumitory – white
Application rate per hectare:
Crop:
Vic: 800 mL
SA: 410 mL
NSW, ACT: 800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 2.5-3.3 L
Critical comments: Spray up to rosette stage.

Weeds controlled: Galvanised Burr
Application rate per hectare:
Pastures - non legumes:
Vic: 4.7 L
NSW, TAS, SA ONLY: 4.7 L
Critical comments: Spray from seedling to pre-flowering.

Weeds controlled: Goosefoots
Application rate per hectare:
Crop:
NSW, ACT: 800 mL

Weeds controlled: Hard Head or Russian Knapweed
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3-5.2 L
Critical comments: Spray before flowering.

Weeds controlled: Hogweed/Wireweed
Application rate per hectare:
Crop:
Vic: 800 mL
SA: 800 mL
NSW, ACT: 800 mL
Qld: 800 mL
Pastures - non legumes:
NSW, TAS, QLD, WA ONLY: 1.15-1.7 L
Critical comments: Spray up to rosette stage.

Weeds controlled: Hoary Cress, Whiteweed
Application rate per hectare:
Crop:
SA: 800 mL
TAS: 800 mL
NSW, ACT: 800 mL
Pastures - non legumes:
Vic: 1.7-3.3 L
NSW, TAS, SA, QLD, WA ONLY: 1.7-2.1 L
Critical comments: Spray from late rosette to pre-flowering.

Weeds controlled: Horehound (seedlings)
Application rate per hectare:
Crop:
SA: 800 mL
WA: 840 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 1.7-3.3 L
Critical comments: Late Autumn to early Spring.

Weeds controlled: Iron Weed, Corn Gromwell
Application rate per hectare:
Crop:
NSW, ACT: 800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 1.15-1.7 L

Weeds controlled: Khaki Weed
Application rate per hectare:
Pastures - non legumes:
NSW, TAS, QLD, WA ONLY: 800 mL-1.15 L
Critical comments: Spray young seedlings only.

Weeds controlled: Lincoln Weed
Application rate per hectare:
Crop:
SA: 800 mL
Critical comments: Autumn spray before sowing improves control.

Weeds controlled: London Rocket
Application rate per hectare:
Crop:
WA: 570 mL
Pastures - non legumes:
WA ONLY: 1.6-2.5 L

Weeds controlled: Lupins
Application rate per hectare:
Crop:
Vic: 800 mL
NSW, ACT: 410-800 mL
Critical comments: Spray up to rosette stage.

Weeds controlled: Melilotus/Hexham Scent
Application rate per hectare:
Crop:
Vic: 800 mL
SA: 800 mL
QLD: 800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 1.15-1.7 L
Critical comments: Spray up to rosette stage.

Weeds controlled: Melons – Camel, paddy
Application rate per hectare:
Crop:
NSW, ACT: 410-800 mL

Weeds controlled: Mustards
Application rate per hectare:
Crop:
Vic: 330 mL
SA: 230-800 mL
TAS: 800 mL
NSW, ACT: 410-800 mL
QLD: 620 mL
WA: 620 mL
Pastures - non legumes:
Vic: 3.3 L
NSW, TAS, SA, QLD, WA ONLY: 1.7-2.5 L
Critical comments: Spray up to rosette stage.

Weeds controlled: Mexican Poppy
Application rate per hectare:
Crop:
SA: 2.3-3.5 L
NSW, ACT: 800 mL
WA: 840 mL
Pastures - non legumes:
NSW, TAS, SA, QLD ONLY: 800 mL-1.15 L
WA ONLY: 1.15-1.5 L
Critical comments: Spray rosette stage and before flowering.

Weeds controlled: Mintweed
Application rate per hectare:
Crop:
NSW, ACT: 800 mL
QLD: 620 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 800 mL-1.15 L
Critical comments: Spray active seedlings only.

Weeds controlled: Muskweed
Application rate per hectare:
Crop:
Vic: 800 mL
Critical comments: Spray up to early rosette stage.

Weeds controlled: New Zealand Spinach
Application rate per hectare:
Crop:
NSW, ACT: 800 mL

Weeds controlled: Noogoora Burr
Application rate per hectare:
Crop:
NSW, ACT: 800 mL
Pastures - non legumes:
Vic: 1.7-3.3 L
NSW, TAS, SA, QLD, WA ONLY: 1.7-3.3 L
Critical comments: Spray seedling to preflowering.

Weeds controlled: Nut Grass
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3-5.2 L
Critical comments: Spray within 4 weeks of foliage emergence, repeat spray necessary.

Weeds controlled: Paterson’s Curse
Application rate per hectare:
Crop:
NSW, ACT: 800 mL
WA: 840 mL
Pastures - non legumes:
Vic: 1.7-3.3 L
NSW, TAS, SA, QLD ONLY: 800 mL-1.7 L
WA ONLY: 1.15-1.5 L
Critical comments: Spray seedling to rosette stage.

Weeds controlled: Poppy Wild
Application rate per hectare:
Crop:
Vic: 410 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 2.1-2.9 L
Critical comments: Spray up to rosette stage.

Weeds controlled: Ragwort
Application rate per hectare:
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 3.3 L
Critical comments: Spray at rosette to cabbage stage.

Weeds controlled: Rapeseed
Application rate per hectare:
Crop:
Vic: 800 mL
NSW, ACT: 410-800 mL
Critical comments: Spray up to rosette stage.

Weeds controlled: Rapistrum
Application rate per hectare:
Crop:
WA: 570 mL
Pastures - non legumes:
WA ONLY: 840 mL

Weeds controlled: Rough Poppy
Application rate per hectare:
Crop:
SA: 410 mL
NSW, ACT: 410-800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 800 mL
Critical comments: Spray young seedlings only.

Weeds controlled: St Johns Wort
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3-5.2 L
NSW, TAS, SA, QLD, WA ONLY: 3.3-4.7 L
Critical comments: Spray before flowering. Spray before plants are 40 cm high.

Weeds controlled: Safflower
Application rate per hectare:
Crop:
NSW, ACT: 410-800 mL

Weeds controlled: Sand Mustard/Sand Rocket
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3 L
Critical comments: Spray before flowering.

Weeds controlled: Shepherd’s Purse
Application rate per hectare:
Crop:
NSW, ACT: 800 mL

Weeds controlled: Silver Leaf Nightshade
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3 L
Critical comments: Spray at flowering. Fallowland: controls top growth only.

Weeds controlled: Skeleton Weed
Application rate per hectare:
Crop:
SA: 800 mL
NSW, ACT: 800 mL
Pastures - non legumes:
Vic: 3.3 L
NSW, TAS, SA, QLD, WA ONLY: 1.15-1.7 L
Critical comments: Spray rosettes before aerial growth commences.

Weeds controlled: Stingless Nettle (Deadnettle)
Application rate per hectare:
Crop:
SA: 800 mL
TAS: 800 mL
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 2.1-2.5 L

Weeds controlled: Stinging Nettle
Application rate per hectare:
Crop:
Vic: 800 mL
Critical comments: Spray up to rosette stage.

Weeds controlled: Stinkwort
Application rate per hectare:
Crop:
NSW, ACT: 800 mL
Pastures - non legumes:
Vic: 1.7-3.3 L
NSW, TAS, SA, QLD, WA ONLY: 1.7-3.3 L
Critical comments: Spray younger plants, use higher rate as plants mature.

Weeds controlled: Storksbill/Erodium
Application rate per hectare:
Crop:
NSW, ACT: 800 mL

Weeds controlled: Sunflower Seedlings
Application rate per hectare:
Crop:
Vic: 800 mL
NSW, ACT: 410-800 mL
QLD: 620 mL
Critical comments: Spray multiple leaves.

Weeds controlled: Golden Thistle
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3
NSW, TAS, SA, QLD, WA ONLY: 3.3
Critical comments: Spray at rosette stage.

Weeds controlled: Nodding Thistle
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3
NSW, TAS, SA, QLD, WA ONLY: 1.15-1.7 L
Critical comments: Spray rosette to preflowering.

Weeds controlled: Saffron Thistle
Application rate per hectare:
Crop:
Vic: 620 mL
SA: 800 mL
NSW, ACT: 410-800 mL
QLD: 800 mL
WA: 800 mL
Pastures - non legumes:
Vic: 800 mL-1.7 L
NSW, TAS, SA, QLD, WA ONLY: 800 mL-2.5 L
Critical comments: Spray up to rosette stage.

Weeds controlled: Sheep Thistle
Application rate per hectare:
Crop:
WA: 840 mL
Pastures - non legumes:
WA ONLY: 840 mL-3.3 L

Weeds controlled: Slender, Shore Thistle
Application rate per hectare:
Crop:
TAS: 800 mL
NSW, ACT: 800 mL
Pastures - non legumes:
Vic: 1.7-3.3 L
NSW, TAS, SA, QLD, WA ONLY: 800 mL-3.3 L
Critical comments: Spray at rosette stage.

Weeds controlled: Soldier Thistle
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3 L
Critical comments: Spray at rosette stage.

Weeds controlled: Spear Thistle
Application rate per hectare:
Crop:
Vic: 800 mL
TAS: 800 mL
Pastures - non legumes:
Vic: 800 mL-2.5 L
NSW, TAS, SA, QLD, WA ONLY: 1.15-2.1 L
Critical comments: Spray at seedling to rosette stage. Use higher rate as plants mature (pastures).

Weeds controlled: Stemless Thistle
Application rate per hectare:
Pastures - non legumes:
Vic: 3.3 L
NSW, TAS, SA, QLD, WA ONLY: 2.5-3.3 L
Critical comments: Spray rosette stage to flowering.

Weeds controlled: St Barnaby’s Thistle
Application rate per hectare:
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 1.15-1.7 L

Weeds controlled: Star Thistle
Application rate per hectare:
Crop:
NSW, ACT: 800 mL
Pastures - non legumes:
Vic: 1.7-3.3 L
NSW, TAS, SA, QLD, WA ONLY: 1.15-1.7 L
Critical comments: Spray seedling to rosette stage. Use higher rate as plants mature.

Weeds controlled: Variegated Thistle
Application rate per hectare:
Crop:
TAS: 800 mL
NSW, ACT: 410-800 mL
QLD: 620 mL
Pastures - non legumes:
Vic: 800 mL-2.5 L
NSW, TAS, SA, QLD, WA ONLY: 800 mL-3.3 L
Critical comments: Spray at rosette stage. Can cause stock poisoning.

Weeds controlled: Thornapple
Application rate per hectare:
Crop:
SA: 3.5 L
NSW, ACT: 410-800 mL
Pastures - non legumes:
Vic: 3.3 L
NSW, TAS, SA, QLD, WA ONLY: 800 mL-1.7 L
Critical comments: Spray at seedling stage.

Weeds controlled: Tree Hogweed
Application rate per hectare:
Crop:
Vic: 800 mL
Critical comments: Spray up to rosette stage.

Weeds controlled: Turnip Weed
Application rate per hectare:
Crop:
SA: 410 mL
NSW, ACT: 410-800 mL
QLD: 410 mL
WA: 620 m
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 800 mL
Critical comments: Spray seedlings only.

Weeds controlled: Vetches/Tares
Application rate per hectare:
Crop:
Vic: 800 mL
SA: 620 mL
TAS: 800 mL

Weeds controlled: Wards Weed
Application rate per hectare:
Crop:
SA: 410 mL
Critical comments: Spray at seedling stage

Weeds controlled: Wild Cabbage
Application rate per hectare:
Crop:
Vic: 800 mL
Critical comments: Spray up to rosette stage.

Weeds controlled: Wild Garlic
Application rate per hectare:
Pastures - non legumes:
Vic: 6.6 L
Critical comments: Suppresses aerial growth only.

Weeds controlled: Wild Mignonette
Application rate per hectare:
Crop:
WA: 840 mL
Pastures - non legumes:
Vic: 3.3 L
Critical comments: Spray at rosette stage.

Weeds controlled: Wild Mustard
Application rate per hectare:
Crop:
WA: 570 mL
Pastures - non legumes:
WA ONLY: 1.6-2.5 L

Weeds controlled: Wild Radish
Application rate per hectare:
Crop:
Vic: 800 mL
SA: 800 mL
TAS: 800 mL
NSW, ACT: 410-800 mL
QLD: 800 mL
WA: 570 mL
Pastures - non legumes:
NSW, TAS, SA, QLD: 800 mL
WA ONLY: 840 mL
Critical comments: Spray up to rosette stage.

Weeds controlled: Wild Sage
Application rate per hectare:
Pastures - non legumes:
NSW, TAS, SA, QLD, WA ONLY: 2.5-3.3 L

Weeds controlled: Wild Teasel
Application rate per hectare:
Pastures - non legumes:
Vic: 1.7-3.3 L
Critical comments: Spray at rosette stage. Use the higher rate as plants mature.

Weeds controlled: Wild Turnip
Application rate per hectare:
Crop:
Vic: 210 mL
SA: 230 mL
TAS: 800 mL
NSW, ACT: 410-800 mL
WA: 400 mL
Pastures - non legumes:
NSW, TAS, SA, QLD: 800 mL
WA ONLY: 840 mL
Critical comments: Spray up to rosette stage.

GENERAL INSTRUCTIONS
Before opening, carefully read Directions For Use, Precautionary Statements, Safety Directions and First Aid Instructions.

RESISTANT WEEDS WARNING
Adama 2,4-D LV ESTER 680 Herbicide is a member of the Phenoxys group of herbicides. 2,4-D LV ESTER 680 has the  isruption of plant cell growth mode of action. For weed resistance management 2,4-D LV ESTER 680 is a Group I herbicide. Some  aturally-occurring weed biotypes resistant to 2,4-D LV ESTER 680 and other Group I herbicides may exist through normal genetic variability in any weed population. The resistant individuals can eventually dominate the weed population if these herbicides are used repeatedly. These resistant weeds will not be controlled by 2,4-D LV ESTER 680 or other Group I herbicides. Since the occurrence of resistant weeds is difficult to detect prior to use, Adama Australia Pty. Ltd. accepts no liability for any losses that may result from the failure of 2,4-D LV ESTER 680 to control resistant weeds.

APPLICATION INFORMATION
This product may be used in either high or low volume sprays. Just pour into water and stir.
BOOM SPRAYING – Use 30-100 litres water per hectare.
AERIAL SPRAYING – Use 10-90 litres water per hectare.
Note: Refer to the Department of Agriculture/Primary Industries in your State for the current restricted spraying areas.

SPRAY APPLICATIONS AND DRIFT RISK MANAGEMENT
USE ONLY when wind speed is more than 3 kilometres per hour or less than 15 km/h, as measured by an anemometer at the application site.
USE ONLY coarse to very coarse spray according to the ASAE S572 definition for standard nozzles.
Checklist:
- Have you cleared/decontaminated your boom sprayer?
- Have you contacted your neighbours prior to spraying?
- Is your sprayer set-up correctly for the particular application?
- Check – boom calibration – at nozzle
– nozzle choice – low drift/what spray quality – coarse to very coarse droplet?
– boom height
– speed or intended application
- You must check, determine and record the weather conditions immediately prior to, and immediately after the spray application is made.
- Record – Temperature
– Relative Humidity
– Delta T
– Wind speed (min 3 km/hr, max 15 km/hr)
– Is there a temperature inversion?
- Night Spraying – Extra care is required to ensure that inversion conditions are not present. Use smoke generator to determine wind direction and presence of inversion conditions.

EQUIPMENT MAINTENANCE AND USAGE
Keep the spray unit for herbicides only if possible. Otherwise wash out the unit with hot soapy water followed by several clear water rinses. DO NOT use wooden spray vats as they cannot be cleaned. Hoses cannot be cleaned and new hoses should be fitted when the unit is to be used for any other purpose.

COMPATIBILITY
This product can be tank mixed with Cutlass 500, Tackle, Spraytop 250, Propon†, Farmozine (500 Flowable and 900 WDG), Lynx 600, Lonestar 750, Trifluralin 480, Wipe-Out CT Elite.

TANK MIXING INSTRUCTIONS
Fill the spray tank 1/4 full with water and agitate. Add wettable powders and water dispersible granules first. Agitate until these are uniformly dispersed, while adding water, until the tank mix is 90% full. Add suspension concentrate (flowables) then soluble concentrates. Add emulsifiable concentrates last. Top up the tank with water and continue agitation until all the ingredients are properly mixed. Observe any mixing sequence instructions specifically stated on the tank mix products.

Registered for culturesRatePreharvest Interval
Spring rye0.21 - 0.8 l7
Winter wheat0.21 - 1.7 l7
Spring wheat0.21 - 0.8 l7
Spring barley0.21 - 0.8 l7
Winter barley0.21 - 1.7 l7
Winter triticale2.1 - 1.7 l7
Spring triticale0.21 - 0.82 l7
Winter rye0.21 - 0.8 l7
Sugarcane1.15 - 2.4 l
Peanuts0.21 - 0.8 l
Canola0.21 - 0.8 l
Potatoes1.15 - 2.4 l
Pasture0.41 - 6.6 l7