Willowood Imidacloprid 4SC

Manufacturer
Willowood
Category
Insecticides
Registered until
N/A
Registration number
87290-26
Active materials
Links

DIRECTIONS FOR USE
It is a violation of Federal Law to use this product in a manner inconsistent with its labeling.
See individual crops for specific pollinator protection application restrictions. If none exist under the specific crop, for foliar applications, follow these application directions for crops that are contracted to have pollinator services for food/feed & commercially grown ornamentals that are attractive to pollinators.

APPLICATION DIRECTIONS
Soil Application:
Direct applications of Willowood Imidacloprid 4SC into the seed or root-zone of crop-. Failure to place Willowood Imidacloprid 4SC into root-zone may result in loss of control or delay in onset of activity. Apply Willowood Imidacloprid 4SC by ground application or chemigation application. For seedling flats or trays, only apply with broadcast, foliar applications or where product is intended to be washed from foliage to soil prior to drying on foliage.
Optimum activity of Willowood Imidacloprid 4SC results from applications to the root-zone of plants to be protected. The earlier Willowood Imidacloprid 4SC is available to a developing plant, the earlier the . protection begins. Willowood Imidacloprid 4SC is continuously taken into the roots over a long period of time and the systemic nature of Willowood Imidacloprid 4SC allows movement from roots through the xylem tissue to all vegetative parts of the plant. This results in extended residual activity of Willowood Imidacloprid 4SC, the control of insects and the prevention and/or reduction of virus transmission or symptom expression, and plant health benefits. The rate of Willowood Imidacloprid 4SC applied affects the length of the plant protection period. Use the higher listed rates when infestations occur later in crop development, or where pest pressure is continuous. Willowood Imidacloprid 4SC will generally not control insects infesting flowers, blooms or fruit. Additional crop protection may be required for insects feeding in, or on these plant parts and for insects not listed in the crop-specific, pests controlled sections of this label. Additional, specific Willowood Imidacloprid 4SC application rates are also provided in the crop-specific sections of this label.

RESTRICTIONS:
• Do not apply with aerial application equipment
• Do not apply more than 0.5 Ib. active ingredient per acre, per year regardless of formulation or method of, application, unless specified within a crop-specific section for a given crop.

MIXING INSTRUCTIONS
Willowood Imidacloprid 4SC is a suspension concentrate (flowable) formulation with unique qualities and should be shaken well prior to measuring/mixing. The formulation is thixotropic and after sitting for a short time reverts to a gel or thick paste consistency helping to prevent phase separation common to most' "flowables". After moderate shaking, the formulation thins to a relatively non-viscous liquid which pours and measures easily with very few trapped air bubbles - another common problem of most fiowables:
Willowood Imidacloprid 4SC has demonstrated easy mixing/blending in water with varying -degrees -ofhardness and temperature. Willowood Imidacloprid 4SC has demonstrated good mixing and compatibility with many fluid fertilizers without dilution with water. However, because fertilizers vary widely in quality arid composition, it is suggested that a jar test be performed (see Compatibility Note below) prior to full-scalemixing. 
To prepare the application mixture, add a portion of the required amount of water to the tank arid with agitation, add \A/illowood Imidacloprid 4SC. Complete filling tank with balance of water needed. Maintain sufficient agitation during both mixing and application. Willowood Imidaclpprid 4SC may also "be"used with other pesticides and/or fertilizer solutions. Please see Compatibility note below. When tank mixtures of
Willowood Imidacloprid 4SC and other pesticides are involved, prepare the tank mixture as described above and follow suggested Mixing Order below. '

Mixing Order
When pesticide mixtures are needed, add wettable powders or wettable granules first, Willowood
Imidacloprid 4SC and other flowable (suspension concentrate) products second, and emulsifiable concentrates last. Ensure good agitation as each component is added. Do hot add an additional component until the previous is thoroughly mixed, if a fertilizer solution is added, a fertilizer/pesticide compatibility agent may be needed. Maintain constant agitation during both mixing and application to ensure uniformity of spray mixture. Follow the most restrictive precautions and limitations on the labeling of all products used in mixtures.

Compatibility Note
Test compatibility of the intended mixture before adding Willowood Imidacloprid 4SC to the spray or mix tank.
Add proportionate amounts of each ingredient in the appropriate order, to a pint or quart jar, cap, shake for 5 miriutes, and let set for 5 minutes. Poor mixing or formation of precipitates that'do not readily redisperse indicates an incompatible mixture that should not be used. For further information, contact your local Willowood representative.

Registered for cultures
Cotton
Peanuts
Soybeans
Tobacco
Cucurbits
Artichokes
Broccoli
Brussels sprouts
Cabbages
Cauliflower