GoldWing

Manufacturer
NUFARM
Category
Herbicides
Registered until
2027-12-31
Registration number
32112
Active materials
Links

DIRECTIONS FOR USE
GoldWing Herbicide is designed for use as a contact and systemic herbicide for broadleaf weed control. GoldWing Herbicide will damage emerged crop plants, even in minute quantities. Apply GoldWing Herbicide prior to the emergence of the crop, either as a preseeding or post-seeding application. GoldWing Herbicide does not provide residual weed control. Only weeds that have emerged at the time of application will be controlled. Apply when weeds are in the seedling stage and actively growing. Pyraflufen-ethyl, a member of the phenyl pyrazole class of herbicides, inhibits the protoporphyrinogen oxidase (PPO) enzyme which results in cell membrane destruction and necrosis. MCPA, a member of the phenoxy class of herbicides, mimics the plant growth regulator indol-3-acetic acid (auxin), interfering with cell enlargement and division, and development in susceptible plants.
Warm, moist growing conditions promote active weed growth and enhance the activity of GoldWing Herbicide by allowing maximum foliar uptake and contact activity. Weeds hardened off by cold weather or drought stress may not be adequately controlled or suppressed and regrowth may occur.
APPLY GoldWing Herbicide WITH GROUND EQUIPMENT ONLY. DO NOT APPLY BY AIR.
For best results, ensure thorough spray coverage of target weeds. Refer to the specific use directions sections of this label for complete use details. Do not permit lactating dairy animals to graze fields within 7 days after application. Do not graze or cut treated crops for forage until 30 days after application. Withdraw meat animals from treated fields at least 3 days before slaughter. 
Field sprayer application: 
DO NOT apply during periods of dead calm. Avoid application of this product when winds are gusty. DO NOT apply with spray droplets smaller than the American Society of Agricultural Engineers (ASAE S572.1) medium classification. Boom height must be 60 cm or less above the crop or ground. DO NOT apply by air.

Buffer Zones: 
Use of the following spray methods or equipment DO NOT require a buffer zone: hand-held or backpack sprayer and spot treatment and soil incorporation. The buffer zones specified in the table below are required between the point of direct application and the closest downwind edge of sensitive terrestrial habitats (such as grasslands, forested areas, shelter belts, woodlots, hedgerows, riparian areas and shrub lands) and sensitive freshwater habitats (such as lakes, rivers, sloughs, ponds, prairie potholes, creeks, marshes, streams, reservoirs and wetlands).
For tank mixes, consult the labels of the tank-mix partners and observe the largest (most restrictive) buffer zone of the products involved in the tank mixture and apply using the coarsest spray (ASAE) category indicated on the labels for those tank mix partners. The buffer zones for this product can be modified based on weather conditions and spray equipment configuration by accessing the Buffer Zone Calculator on the Pest Management Regulatory Agency web site.

REGISTERED CROPS: 
GoldWing Herbicide can be applied pre-seeding or post-seeding prior to crop emergence in the crops from the crop groups listed below as well as canary seed (Phalaris canariensis). Crops not listed can be planted one month after GoldWing Herbicide application. 

Crop Group 6: Legume Vegetable
Field pea 
Crop Group 15: Cereal Grains 
Barley, buckwheat, corn (sweet and field), pearl millet, proso millet, oats, popcorn, rye (spring and winter), triticale and wheat (spring, durum, winter)

MIXING INSTRUCTIONS: 
1. Select a spray volume and nozzle type that will ensure thorough coverage and uniform spray pattern. Use a minimum of 50 - 100 L spray volume per hectare.
2. Fill the spray tank 1/3 full with fresh water and start agitation.
3. If tankmixing with glyphosate, add the required amount of glyphosate to the tank first, agitate well. Always consult the label of the tank mix partner(s) for minimum spray volume requirements and apply the tank mixture using a water volume recommended for all products.
4. Add the required amount of GoldWing Herbicide to the tank, agitate well.
5. Continue to fill tank and maintain agitation for at least 5 minutes to ensure thorough mixing.
6. Use the spray preparation of GoldWing Herbicide within 24 hours. Product degradation may occur under alkaline conditions (pH >7.5). If spray solution is left standing without agitation, thoroughly agitate before resuming the spraying operation.

APPLICATION INSTRUCTIONS: 
Apply the spray mixture uniformly with properly calibrated ground equipment only. Ensure thorough coverage and a uniform spray pattern. Flat fan nozzles are recommended (minimum 50 - 100 L spray volume per hectare). Use 50 mesh filter screens or larger (metal or nylon). A spray pressure of 210 - 275 kPa is recommended. Apply uniformly.

GoldWing Herbicide ALONE 
Apply 330 – 660 mL of GoldWing Herbicide per hectare prior to wheat, barley, oats, rye, buckwheat, pearl millet, proso millet, triticale, canary seed, peas and corn

Timing:
For best results apply to emerged, young, actively growing weeds that are less than 5 cm tall or across. Thorough coverage of target weeds is essential. GoldWing Herbicide can only be applied once per year. Weed control may be reduced if the plants are beyond the recommended application growth stage, and during stress conditions, e.g. drought, heat or cold stress, or in heavy infestations where overlapping leaves prevent spray contact. In these situations, use up to 660 mL/ha.

GoldWing Herbicide + Glyphosate 
Apply GoldWing Herbicide tank mixed with glyphosate prior to seeding or post-seeding before crop emergence. Rates and formulation of glyphosate are detailed in the following table. Follow all precautions, limitations, timing recommendations, crop rotations and sprayer cleanup on the tank mix partner product label.
Higher rates of glyphosate may be recommended in some situations. Refer to the glyphosate product label for further effective rates. 

Weeds controlled: All weeds controlled by GoldWing Herbicide and glyphosate alone (see the tank mix partner label). For weeds that are not controlled by the chosen rate of glyphosate, apply the tank mixture in accordance with the recommended timing for control of the weed with GoldWing Herbicide alone. In some cases, tank mixing a pest control product with another pest control product or a fertilizer can result in biological effects that could include, but are not limited to: reduced pest efficacy or increased host crop injury. The user should contact Nufarm Agriculture Inc. at 1-800-868-5444 for information before mixing any pesticide or fertilizer that is not specifically recommended on this label. The user assumes the risk of losses that result from the use of tank mixes that do not appear on this label or that are not specifically recommended by Nufarm Agriculture Inc.

SPRAYER CLEANUP: 
To avoid subsequent injury to crops, immediately after spraying and prior to spraying other crops, thoroughly remove all traces of GoldWing Herbicide from mixing and spray equipment as follows:
Drain tank; then flush tank, boom and hoses with clean water for a minimum of ten minutes.
Next, prepare a sprayer cleaning solution by adding 3 litres of ammonia (containing at least 3% active) per 100 litres of clean water. Prepare sufficient cleaning solution to allow the operation of the spray system for a minimum of 15 minutes to thoroughly flush the tank, hoses, spray boom and spray nozzles.
If possible, leave the ammonia solution or fresh water left in the spray tank, hoses, spray booms and spray nozzles overnight or during storage to dissolve and dilute any remaining traces of herbicide.
Nozzles and screens may be cleaned separately in a bucket containing cleaning agent and water.
DO NOT contaminate irrigation or drinking water supplies or aquatic habitats by cleaning of equipment or disposal of wastes.

RESISTANCE MANAGEMENT RECOMMENDATIONS: 
For resistance management, GoldWing Herbicide is a Group 4 and 14 herbicide. Any weed population may contain or develop plants naturally resistant to GoldWing Herbicide and other Group 4 and 14 herbicides. The resistant biotypes may dominate the weed population if these herbicides are used repeatedly in the same field. Other resistance mechanisms that are not linked to site of action, but specific for individual chemicals, such as enhanced metabolism, may also exist. Appropriate resistance-management strategies should be followed.
To delay herbicide resistance:
Where possible, rotate the use of GoldWing Herbicide or other Group 4 and 14 herbicides with different herbicide groups that control the same weeds in a field.
Use tank mixtures with herbicides from a different group when such use is permitted. To delay resistance, the less resistance-prone partner should control the target weed(s) as effectively as the more resistance-prone partner.
Herbicide use should be based on an integrated weed management program that includes scouting, historical information related to herbicide use and crop rotation, and considers tillage (or other mechanical control methods), cultural (for example, higher crop seeding rates; precision fertilizer application method and timing to favour the crop and not the weeds), biological (weed-competitive crops or varieties) and other management practices.
Monitor weed populations after herbicide application for signs of resistance development (for example, only one weed species on the herbicide label not controlled). If resistance is suspected, prevent weed seed production in the affected area if possible by an alternative herbicide from a different group. Prevent movement of resistant weed seeds to other fields by cleaning harvesting and tillage equipment when moving between fields, and planting clean seed.
Have suspected resistant weed seeds tested by a qualified laboratory to confirm resistance and identify alternative herbicide options.
Contact your local extension specialist or certified crop advisors for any additional pesticide resistance-management and/or integrated weed-management recommendations for specific crops and weed biotypes.

Registered for culturesRate
Sweet corn330 - 660 ml
Millet330 - 660 ml
Winter wheat330 - 660 ml
Spring wheat330 - 660 ml
Spring barley330 - 660 ml
Winter barley330 - 660 ml
Spring oats330 - 660 ml
Winter oats330 - 660 ml
Winter rye330 - 660 ml
Spring rye330 - 660 ml
Buckwheat330 - 660 ml
Winter triticale330 - 660 ml
Spring triticale330 - 660 ml
Peas330 - 660 ml
Corn330 - 660 ml